PRIYADARSHINI, Jayaraju, Mariappan PREMALATHA, Robert ČEP, Murugan JAYASUDHA a Kanak KALITA. Analyzing Physics-Inspired Metaheuristic Algorithms in Feature Selection with K-Nearest-Neighbor. Applied Sciences. BASEL: MDPI Open Access Publishing, 2023, 13(2), s. nestránkováno. ISSN 2076-3417. [Detail]

GANESH, Narayanan, Rajendran SHANKAR, Robert ČEP, Shankar CHAKRABORTY a Kanak KALITA. Efficient Feature Selection Using Weighted Superposition Attraction Optimization Algorithm. Applied Sciences. BASEL: MDPI Open Access Publishing, 2023, 13(5), s. nestránkováno. ISSN 2076-3417. [Detail]

ČEPOVÁ, Lenka, Robert ČEP, Leszek CHALKO, Stepanka DVORACKOVA, Miroslav TROCHTA, Miroslaw RUCKI, Libor BERANEK, Ondřej MIZERA a Volodymyr CHYSHKALA. The Effect of Cutting Tool Geometry on Surface Integrity: A Case Study of CBN Tools and the Inner Surface of Bearing Rings. Applied Sciences. BASEL: MDPI Open Access Publishing, 2023, 13(6), s. nestránkováno. ISSN 2076-3417. [Detail]

WILLIAM, Mathias Vijay Albert, Subramanian RAMESH, Robert ČEP, Siva Kumar MAHALINGAM a Muniyandy ELANGOVAN. DPGWO Based Feature Selection Machine Learning Model for Prediction of Crack Dimensions in Steam Generator Tubes. Applied Sciences. BASEL: MDPI Open Access Publishing, 2023, 13(14), s. nestránkováno. ISSN 2076-3417. [Detail]

KUMAR, M. Guru Vimal, N. VEENA, Lenka ČEPOVÁ, M. Arun Manicka RAJA, Allam BALARAM a Muniyandy ELANGOVAN. Evaluation of the Quality of Practical Teaching of Agricultural Higher Vocational Courses Based on BP Neural Network. Applied Sciences. MDPI Open Access Publishing, 2023, 13(2), s. nestránkováno. ISSN 2076-3417. [Detail]

KUMARAN, Narayanan, Annamalai MEENAKSHI, Robert ČEP, Jayavelu Udaya PRAKASH a Ondřej MIZERA. Equitable and Paired Equitable Domination in Inflated Graphs and Their Complements. Axioms. BASEL: MDPI Open Access Publishing, 2023, 12(12), s. nestránkováno. ISSN 2075-1680. [Detail]

GARUS, Sebastian, Justyna GARUS, Wojciech SOCHACKI, Marcin NABIALEK, Jana PETRŮ, Wojciech BOREK, Michal ŠOFER a Pawel KWIATON. Influence of material distribution and damping on the dynamic stability of Bernoulli-Euler beams. Bulletin of the Polish Academy of Sciences: Technical Sciences. Varšava: Polska akademia nauk (PAN), 2023, 71(4), s. nestránkováno. ISSN 0239-7528. [Detail]

GARUS, Sebastian, Wojciech SOCHACKI, Pawel KWIATON, Marcin NABIALEK, Jana PETRŮ a Mariusz KUBANEK. Influence of spatial distribution and the type of material on the occurrence of bandgaps in phononic crystals. Bulletin of the Polish Academy of Sciences: Technical Sciences. Varšava: Polska akademia nauk (PAN), 2023, 71(3), s. nestránkováno. ISSN 0239-7528. [Detail]

MIZERA, Ondřej, Lenka ČEPOVÁ, Jozef TKÁČ, Vieroslav MOLNÁR, Gabriel FEDORKO a Steven SAMBORSKI. Study of the influence of optical measurement of slope geometry in the working chamber for AISI 316L. Composite Structures. San Diego: Elsevier, 2023, 321(117291), s. nestránkováno. ISSN 0263-8223. [Detail]

NGUYEN, Hoang-Sy, Huynh-Cong DANH, Phu MA QUOC, Jakub MĚSÍČEK, Jiří HAJNYŠ, Marek PAGÁČ a Jana PETRŮ. A Bibliometrics Analysis of Medical Internet of Things for Modern Healthcare. Electronics. BASEL: MDPI Open Access Publishing, 2023, 12(22), s. nestránkováno. ISSN 2079-9292. [Detail]

KHAN, R., A.-H.I. MOURAD, A.H. SEIKH, Jana PETRŮ a H. H.YA. Erosion impact on mild steel elbow pipeline for different orientations under liquid-gas-sand annular flow. Engineering Failure Analysis. Oxford: PERGAMON-ELSEVIER SCIENCE LTD, 2023, 153(1), s. nestránkováno. ISSN 1350-6307. [Detail]

STOLARIK, Gabriel, Dagmar KLICHOVA, Jakub POLOPRUDSKY, Akash NAG a Sergej HLOCH. Assessment of surface irregularities created by controlled liquid droplet on the surface of stainless steel AISI 304L. Engineering Science and Technology, an International Journal. San Diego: Elsevier, 2023, 47(47), s. nestránkováno. ISSN 2215-0986. [Detail]

RAHMAN, Md. Mahbubur, Ved PRAKASH, Sunil CHANDEL, D. G THAKUR, Robert ČEP, Nitin KHEDKAR, Sachin SALUNKHE a Emad S ABOUEL NASR. Analysis of the aerodynamic characteristics of an ejection seat system using computational fluid dynamics. Frontiers in Mechanical Engineering - Switzerland. LAUSANNE: Frontiers, 2023, 9(9), s. nestránkováno. ISSN 2297-3079. [Detail]

PRAKASH, Jayavelu Udaya, Subramani ANANTH, Sunder Jebarose JULIYANA, Robert ČEP, Nitin KHEDKAR, Sachin SALUNKHE, Emad Abouel NASR a Ali KAMRANI. Parametric optimization of wear parameters of hybrid composites (LM6/B₄C/fly ash) using Taguchi technique. Frontiers in Mechanical Engineering - Switzerland. LAUSANNE: Frontiers, 2023, 9(9), s. nestránkováno. ISSN 2297-3079. [Detail]

GHADAI, Ranjan Kumar, G. SHANMUGASUNDAR, Lenka ČEPOVÁ, Soham DAS, Premchand Kumar MAHTO a Kanak KALITA. A temperature-based synthesis and characterization study of aluminum-incorporated diamond-like carbon thin films. Frontiers in Mechanical Engineering - Switzerland. LAUSANNE: Frontiers, 2023, 9(9), s. nestránkováno. ISSN 2297-3079. [Detail]

DWIVEDI, Suryank, Amit Rai DIXIT, Alok Kumar DAS a Akash NAG. A Novel Additive Texturing of Stainless Steel 316L Through Binder Jetting Additive Manufacturing. International Journal of Precision Engineering and Manufacturing-Green Technology. Soul: Korean Society for Precision Engineeing, 2023, 2023(17/03/2023), s. nestránkováno. ISSN 2288-6206. [Detail]

SRIVASTAVA, Ashish Kumar, Ajay KUMAR, Parveen KUMAR, Preeti GAUTAM a Namrata DOGRA. Research Progress in metal additive manufacturing: Challenges and Opportunities. International Journal on Interactive Design and Manufacturing. Vídeň: Springer, 2023, 2023(DECEMBER 2023), s. 1-17. ISSN 1955-2513. [Detail]

SINGH, Aditya, Ashish Kumar SRIVASTAVA, Ajay KUMAR a Preeti GAUTAM. Design for low thermal conductivity and low vibrational impact without efflorescence of the composite bricks developed by waste plastic resin/fly ash/glass powder/gypsum. International Journal on Interactive Design and Manufacturing. Vídeň: Springer, 2023, 2023(OCTOBER 2023), s. nestránkováno. ISSN 1955-2513. [Detail]

KHAN, Rehan, Jana PETRŮ a A. H SEIKH. Erosion prediction due to micron-sized particles in the multiphase flow of T and Y pipes of oil and gas fields. International journal of pressure vessels and piping. San Diego: Elsevier, 2023, 206(1), s. nestránkováno. ISSN 0308-0161. [Detail]

DVORSKÝ, Richard, Jana KUKUTSCHOVÁ, Marek PAGÁČ, Ladislav SVOBODA, Zuzana ŠIMONOVÁ, Kateřina PETEREK DĚDKOVÁ, Jiří BEDNÁŘ, Rafael MENDES, Dalibor MATÝSEK, Ondřej MALINA, Jiří TUČEK, Zuzana VILAMOVÁ, Sergei KISELEV, Thomas GEMMING a Peter FILIP. Analysis and Modelling of Single Domain Core-Shell (αFeNi/chromite) Nanoparticles Emitted during Selective Laser Melting, and their Magnetic Remanence. Journal of Cleaner Production. Elsevier, 2023, 400(MAY 10 2023), s. 1-10. ISSN 0959-6526. [Detail]

JANSA, Jan, Anastasia VOLODARSKAJA, Josef HLINKA, Lucie ZARYBNICKA, Stanislav POLZER, Martin KRAUS, Jiří HAJNYŠ, David SCHWARZ a Marek PAGÁČ. Corrosion and material properties of 316L stainless steel produced by material extrusion technology. Journal of Manufacturing Processes. San Diego: Elsevier, 2023, 88(88), s. 232-245. ISSN 1526-6125. [Detail]

STOLÁRIK, G., J. SVOBODOVÁ, D. KLICHOVÁ, Akash NAG a S. HLOCH. Titanium surface roughening with ultrasonic pulsating water jet. Journal of Manufacturing Processes. San Diego: Elsevier, 2023, 90(24/03/2023), s. 341-356. ISSN 1526-6125. [Detail]

PELIKAN, Lukas, Michal SLANY, Ondrej STRANSKY, Libor BERANEK, Zdenek PITRMUC, Lenka ČEPOVÁ a Stepanka DVORACKOVA. Novel drill geometries for dry drilling of stainless steel. Journal of Manufacturing Processes. San Diego: Elsevier, 2023, 92(92), s. 500-520. ISSN 1526-6125. [Detail]

GRAF, Alexander, Verena KRAEUSEL, Dieter WEISE, Jana PETRŮ, Jiří KOZIOREK a Pravishan BHANDARI. Determination of the Influence of the Tool Side Stress Superposition and Tool Geometry on the Cut Surface Quality during Precision Shear Cutting. Journal of Manufacturing and Materials Processing. BASEL: MDPI Open Access Publishing, 2023, 7(4), s. nestránkováno. ISSN 2504-4494. [Detail]

NESLUSAN, Miroslav, K. ZGUTOVA, Robert ČEP, M. PITONAK a F. ANDEJKA. Barkhausen noise emission in soft magnetic ribbons heat treated in an external magnetic field. Journal of magnetism and magnetic materials. San Diego: Elsevier, 2023, 572(March), s. nestránkováno. ISSN 0304-8853. [Detail]

KROL, Mariusz a Jiří HAJNYŠ. Calorimetric analysis of Mg-Li ultra light magnesium alloy. Journal of thermal analysis and calorimetry. Vídeň: Springer, 2023, 2023(JUL 2023), s. 1-9. ISSN 1388-6150. [Detail]

BACHCHHAV, Bhanudas D. D., Shrikant V. V. CHAITANYA, Sachin SALUNKHE, Palanisamy CHANDRAKUMAR, Marek PAGÁČ a Emad Abouel NASR. Wear Performance of Cu-Cd, Cu-Be and Cu-Cr-Zr Spot Welding Electrode Materials. Lubricants. BASEL: MDPI Open Access Publishing, 2023, 11(7), s. 1-15. ISSN 2075-4442. [Detail]

NGUYEN, Hoang-Sy, Phu MA QUOC, Jiří HAJNYŠ, Jakub MĚSÍČEK a Marek PAGÁČ. RESEARCH TREND IN THE FIELD OF ADDITIVE MANUFACTURING WITH BIBLIOMETRICS STUDY. MM Science Journal. Praha: MM Publishing, 2023, 2023(June 2023), s. 6534-6537. ISSN 1803-1269. [Detail]

BLÁHA, Roman, Dominik KRIŠÁK, Jiří HAJNYŠ, Jakub MĚSÍČEK, Marek PAGÁČ, Lukáš JANČAR, Jan JANSA, Eliška POSMYKOVÁ a Marek GAZDA. EXPERIMENTAL VERIFICATION OF PROCESS PARAMETERS INFLUENCING THE MECHANICAL PROPERTIES OF M300 IN THE SLM PROCESS. MM Science Journal. Praha: MM Publishing, 2023, 2023(JUNE 2023), s. 6555-6560. ISSN 1803-1269. [Detail]

MACHAC, T., Peter POKORNÝ, Jana PETRŮ, J. HRBAL, M. KURUC a T. VOPAT. ADITIVE MANUFACTURING OF M300 STEEL CUTTING TOOLS BY SELECTIVE LASER MELTING. MM Science Journal. Praha: MM Publishing, 2023, 10(1), s. 6735-6740. ISSN 1803-1269. [Detail]

POSMYKOVÁ, Eliška, Marek GAZDA a Jakub MĚSÍČEK. TOPOLOGICAL OPTIMIZATION OF THE ROCKER ARM. MM Science Journal. MM Publishing, 2023, 2023-June(June 2023), s. 6545-6549. ISSN 1803-1269. [Detail]

SLANINKOVÁ, Aneta, Jan JANSA, Radim JANECZKO, Ivan MRKVICA, Marek PAGÁČ a Tibor JURGA. EFFECT OF CUTTING EDGE PREPARATION TECHNOLOGIES ON SURFACE ROUGHNESS , PROCESSING TIME AND K- FACTOR. MM Science Journal. MM Publishing, 2023, 2023(June), s. 6550-6554. ISSN 1803-1269. [Detail]

SIDDIQUE, M. Zeeshan, Muhammad Iftikhar FARAZ, Shahid Ikramullah BUTT, Rehan KHAN, Jana PETRŮ, Syed Husain Imran JAFFERY, Muhammad Ali KHAN a Abdul Malik TAHIR. Parametric Analysis of Tool Wear, Surface Roughness and Energy Consumption during Turning of Inconel 718 under Dry, Wet and MQL Conditions. Machines. BASEL: MDPI Open Access Publishing, 2023, 11(11), s. nestránkováno. ISSN 2075-1702. [Detail]

ZÁRYBNICKÁ, L., Marek PAGÁČ, R. ŠEVČÍK, J. POKORNÝ a M. MAREK. Effect of Topology Parameters on Physical–Mechanical Properties of Magnetic PLA 3D-Printed Structures. Magnetochemistry. Basilej: MDPI Open Access Publishing, 2023, 9(12), s. nestránkováno. ISSN 2312-7481. [Detail]

SHANMUGASUNDAR, G., Ankur BANSOD, Vladimíra SCHINDLEROVÁ a Robert ČEP. Influence of Filler Material on the Microstructural and Mechanical Properties of 430 Ferritic Stainless Steel Weld Joints. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(4), s. nestránkováno. ISSN 1996-1944. [Detail]

MICIETOVA, Anna, Maria CILLIKOVA, Robert ČEP, Miroslav NESLUSAN a Nikolaj GANEV. Study of Residual Stresses and Austenite Gradients in the Surface after Hard Turning as a Function of Flank Wear and Cutting Speed. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(4), s. nestránkováno. ISSN 1996-1944. [Detail]

ARIVALAGAN, Suresh, Rajakumar SAPPANI, Robert ČEP a Mahalingam Siva KUMAR. Optimization and Experimental Investigation of 3D Printed Micro Wind Turbine Blade Made of PLA Material. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(6), s. nestránkováno. ISSN 1996-1944. [Detail]

MIKULIKOVA, Aleksandra, Jakub MĚSÍČEK, Jan KARGER, Jiří HAJNYŠ, Phu MA QUOC, Aleš SLÍVA, Jakub ŠMIRAUS, Dávid SRNÍČEK, Samuel CIENCIALA a Marek PAGÁČ. Topology Optimization of the Clutch Lever Manufactured by Additive Manufacturing. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(9), s. nestránkováno. ISSN 1996-1944. [Detail]

JULIYANA, Sunder Jebarose, Jayavelu Udaya PRAKASH, Robert ČEP a Krishnasamy KARTHIK. Multi-Objective Optimization of Machining Parameters for Drilling LM5/ZrO2 Composites Using Grey Relational Analysis. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(10), s. nestránkováno. ISSN 1996-1944. [Detail]

NAG, Akash, Madhulika SRIVASTAVA, Jana PETRŮ, Petra VÁŇOVÁ, Ashish Kumar SRIVASTAVA a Sergej HLOCH. Comparison of Continuous and Pulsating Water Jet during Piercing of Ductile Material. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(9), s. nestránkováno. ISSN 1996-1944. [Detail]

GHADAI, Ranjan Kumar, Kamaraj LOGESH, Robert ČEP, Jasgurpreet Singh CHOHAN a Kanak KALITA. Influence of Deposition Time on Titanium Nitride (TiN) Thin Film Coating Synthesis Using Chemical Vapour Deposition. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(13), s. nestránkováno. ISSN 1996-1944. [Detail]

DEVI, C, Siva Kumar MAHALINGAM, Robert ČEP a Karel KOURIL. Effect of Cryo-Treated Cutting Tool End Milling on Custom 450 Stainless Steel. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(13), s. nestránkováno. ISSN 1996-1944. [Detail]

DEREJE, Teshome, Sivaprakasam PALANI, Melaku DESTA a Robert ČEP. Experimental Investigation into the Influence of the Process Parameters of Wire Electric Discharge Machining Using Nimonic-263 Superalloy. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(15), s. nestránkováno. ISSN 1996-1944. [Detail]

FOJTÍK, František, Roman POTROK, Jiří HAJNYŠ, Phu MA QUOC, Lukáš KUDRNA a Jakub MĚSÍČEK. Quantification and Analysis of Residual Stresses in Braking Pedal Produced via Laser-Powder Bed Fusion Additive Manufacturing Technology. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(17), s. nestránkováno. ISSN 1996-1944. [Detail]

GEL'ATKO, Matus, Michal HATALA, Frantisek BOTKO, Radoslav VANDZURA, Jiří HAJNYŠ, Michal SAJGALIK a Jozef TOROK. Stress Relieving Heat Treatment of 316L Stainless Steel Made by Additive Manufacturing Process. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(19), s. nestránkováno. ISSN 1996-1944. [Detail]

GNATOWSKI, Adam, Rafal GOLEBSKI, Piotr SIKORA, Jana PETRŮ a Jiří HAJNYŠ. Analysis of the Impact of Changes in Thermomechanical Properties of Annealed Semi-Crystalline Plastics on the Surface Condition after the Machining Process. Materials. BASEL: MDPI Open Access Publishing, 2023, 16(13), s. nestránkováno. ISSN 1996-1944. [Detail]

POKORNÝ, Peter, Delgado SOBRINO, Štefan VÁCLAV, Jana PETRŮ a Rafal GOLEBSKI. Research into Specific Mechanical Properties of Composites Produced by 3D-Printing Additive Continuous-Fibe. Materials. MDPI Open Access Publishing, 2023, 16(4), s. 1-21. ISSN 1996-1944. [Detail]

SRIVASTAVA, A.K., S. DWIVEDI, Akash NAG, D. KUMAR, A.R. DIXIT a Sergej HLOCH. Microstructural, mechanical and tribological performance of a magnesium alloy AZ31B/Si3N4/eggshell surface composite produced by solid-state multi-pass friction stir processing. Materials Chemistry and Physics. Lausanne: Elsevier Science SA, 2023, 301(127694), s. nestránkováno. ISSN 0254-0584. [Detail]

SNOPINSKI, P, Ondřej HILŠER a Jiří HAJNYŠ. Tuning the defects density in additively manufactured fcc aluminium alloy via modifying the cellular structure and post-processing deformation. Materials Science and Engineering. A, Structural Materials : Properties, Microstructure and Processing. Lausanne: Elsevier Science SA, 2023, 865(February), s. nestránkováno. ISSN 0921-5093. [Detail]

VASUKI, Manimozhi, Ramachandramoorthi SHANMUGAPRIYA, Miroslav MAHDAL a Robert ČEP. A Study on Fuzzy Resolving Domination Sets and Their Application in Network Theory. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(2), s. nestránkováno. ISSN 2227-7390. [Detail]

VIMALA, Ramasamy, Ramasamy KODEESWARAN, Robert ČEP, Majella Jenvi Ignatia KRISHNASAMY, Meenakshi AWASTHI a Govindasamy SANTHAKUMAR. Oscillation of Nonlinear Neutral Delay Difference Equations of Fourth Order. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(6), s. nestránkováno. ISSN 2227-7390. [Detail]

SRIREKHA, B., Shakeela SATHISH, R. Narmada DEVI, Miroslav MAHDAL, Robert ČEP a K. ELAVARASAN. Attributes Reduction on SE-ISI Concept Lattice for an Incomplete Context Using Object Ranking. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(7), s. nestránkováno. ISSN 2227-7390. [Detail]

NARAYANAN, Rama Chandran, Narayanan GANESH, Robert ČEP, Pradeep JANGIR, Jasgurpreet Singh CHOHAN a Kanak KALITA. A Novel Many-Objective Sine-Cosine Algorithm (MaOSCA) for Engineering Applications. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(10), s. nestránkováno. ISSN 2227-7390. [Detail]

REDDY, Nagireddy Venkata, Pydimarri PADMAJA, Miroslav MAHDAL, Selvaraj SEERANGAN, Vrince VIMAL, Vamsidhar TALASILA a Lenka ČEPOVÁ. Hybrid Fuzzy Rule Algorithm and Trust Planning Mechanism for Robust Trust Management in IoT-Embedded Systems Integration. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(11), s. nestránkováno. ISSN 2227-7390. [Detail]

SHANMUGAPRIYA, Ramachandramoorthi, Perichetla Kandaswamy HEMALATHA, Lenka ČEPOVÁ a Jiří STRUŽ. A Study of Independency on Fuzzy Resolving Sets of Labelling Graphs. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(16), s. nestránkováno. ISSN 2227-7390. [Detail]

JAGADEESAN, Viswanath, Thilagavathi RAJAMANICKAM, Vladimíra SCHINDLEROVÁ, Sreelakshmi SUBBARAYAN a Robert ČEP. A Study on Two-Warehouse Inventory Systems with Integrated Multi-Purpose Production Unit and Partitioned Rental Warehouse. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(18), s. nestránkováno. ISSN 2227-7390. [Detail]

MEENAKSHI, Annamalai, Adhimoolam KANNAN, Robert ČEP a Muniyandy ELANGOVAN. Efficient Graph Network Using Total Magic Labeling and Its Applications. Mathematics. BASEL: MDPI Open Access Publishing, 2023, 11(19), s. nestránkováno. ISSN 2227-7390. [Detail]

ZARYBNICKA, Lucie, Jana MACHOTOVA, Marek PAGÁČ, Jozef RYCHLY a Anna VYKYDALOVA. The effect of filling density on flammability and mechanical properties of 3D-printed carbon fiber-reinforced nylon. Polymer testing. San Diego: Elsevier, 2023, 120(107944), s. nestránkováno. ISSN 0142-9418. [Detail]

ZUROWSKI, Wojciech, Jaroslaw ZEPCHLO, Robert ČEP, Lenka ČEPOVÁ, Miroslaw RUCKI, Zbigniew KRZYSIAK, Jacek CABAN a Waldemar SAMOCIUK. The Effect of Powder and Emulsion Binders on the Tribological Properties of Particulate Filled Glass Fiber Reinforced Polymer Composites. Polymers. BASEL: MDPI Open Access Publishing, 2023, 15(1), s. nestránkováno. ISSN 2073-4360. [Detail]

RAJESH, Durvasulu, Nagarajan LENIN, Robert ČEP, Palanivel ANAND a Muniyandy ELANGOVAN. Enhancement of Thermal Behaviour of Flax with a Ramie Fibre-Reinforced Polymer Composite. Polymers. BASEL: MDPI Open Access Publishing, 2023, 15(2), s. nestránkováno. ISSN 2073-4360. [Detail]

RAMESH, Velumayil, Krishnasamy KARTHIK, Robert ČEP a Muniyandy ELANGOVAN. Influence of Stacking Sequence on Mechanical Properties of Basalt/Ramie Biodegradable Hybrid Polymer Composites. Polymers. BASEL: MDPI Open Access Publishing, 2023, 15(4), s. nestránkováno. ISSN 2073-4360. [Detail]

PAUL, D. L. Belgin, Ayyappan Susila PRAVEEN, Lenka ČEPOVÁ a Muniyandy ELANGOVAN. Rheological Behavior and Printability Study of Tri-Calcium Phosphate Ceramic Inks for Direct Ink Writing Method. Polymers. BASEL: MDPI Open Access Publishing, 2023, 15(6), s. nestránkováno. ISSN 2073-4360. [Detail]

ŠOFER, Michal, Pavel ŠOFER, Marek PAGÁČ, Anastasia VOLODARSKAJA, Marek BABIUCH a Filip GRUŇ. Acoustic Emission Signal Characterisation of Failure Mechanisms in CFRP Composites Using Dual-Sensor Approach and Spectral Clustering Technique. Polymers. Basilej: MDPI Open Access Publishing, 2023, 15(1), s. nestránkováno. ISSN 2073-4360. [Detail]

KARTHICK, Muniyappan, Ekambaram PAVITHRA, Robert ČEP a Muniyandy ELANGOVAN. Machining of Custom-450 Grade Stainless Steel Using TiAlSiN-Coated Tungsten Carbide Tool Inserts. Processes. BASEL: MDPI Open Access Publishing, 2023, 11(4), s. nestránkováno. ISSN 2227-9717. [Detail]

SHANMUGASUNDAR, G., Kamaraj LOGESH, Robert ČEP a Ranendra ROY. Evaluating Eco-Friendly Refrigerant Alternatives for Cascade Refrigeration Systems: A Thermoeconomic Analysis. Processes. BASEL: MDPI Open Access Publishing, 2023, 11(6), s. nestránkováno. ISSN 2227-9717. [Detail]

SHANMUGASUNDAR, G., Kanak KALITA, Robert ČEP a Jasgurpreet Singh CHOHAN. Decision Models for Selection of Industrial Robots-A Comprehensive Comparison of Multi-Criteria Decision Making. Processes. BASEL: MDPI Open Access Publishing, 2023, 11(6), s. nestránkováno. ISSN 2227-9717. [Detail]

KUMAR, T. Satish, Titus THANKACHAN, S. SHALINI, Robert ČEP a Kanak KALITA. Microstructure, hardness and wear behavior of ZrC particle reinforced AZ31 surface composites synthesized via friction stir processing. Scientific Reports. New York: Nature Publishing Group, 2023, 13(1), s. nestránkováno. ISSN 2045-2322. [Detail]

HEMA, Prianka, Rejin PAUL, Lenka ČEPOVÁ, Bhola KHAN, Kailash KUMAR a Vladimíra SCHINDLEROVÁ. Complexity and Monitoring of Economic Operations Using a Game-Theoretic Model for Cloud Computing. Systems. BASEL: MDPI Open Access Publishing, 2023, 11(2), s. nestránkováno. ISSN 2079-8954. [Detail]

BALARAM, Allam, K. Nattar KANNAN, Lenka ČEPOVÁ, M. Kishore KUMAR, B. Swaroopa RANI a Vladimíra SCHINDLEROVÁ. Artificial Intelligence for Media Ecological Integration and Knowledge Management. Systems. BASEL: MDPI Open Access Publishing, 2023, 11(5), s. nestránkováno. ISSN 2079-8954. [Detail]

SRIVASTAVA, Ashish Kumar, Akash NAG, Suryank DWIVEDI, Amit Rai DIXIT a Sergej HLOCH. Effect of eggshell powder on the microstructural and thermal behavior of Al7075/waste eggshell surface composites produced by solid-state friction stir processing developed for potential thermal applications. The international journal of advanced manufacturing technology. Vídeň: Springer, 2023, 127(25 MAY 2023), s. 1243-1261. ISSN 0268-3768. [Detail]

DIXIT, A.R., A.K. SRIVASTAVA, S. DWIVEDI, Akash NAG a Sergej HLOCH. An investigation on microstructural features and bonding strength of magnesium-based multifunctional laminated composite developed by friction stir additive manufacturing. The international journal of advanced manufacturing technology. Vídeň: Springer, 2023, 128(09/2023), s. 531-546. ISSN 0268-3768. [Detail]

KLICHOVA, D., Akash NAG, J. POLOPRUDSKÝ, J. FOLDYNA, F. PUDE, L. SITEK a S. HLOCH. Utilising of water hammer effect for surface roughening of Ti6Al4V. The international journal of advanced manufacturing technology. Vídeň: Springer, 2023, 126(06/2023), s. 5633-5647. ISSN 0268-3768. [Detail]

CHLUPOVA, Alice, Sergej HLOCH, Akash NAG, Ivo SULAK a Tomas KRUML. Effect of pulsating water jet processing on erosion grooves and microstructure in the subsurface layer of 25CrMo4 (EA4T) steel. Wear. Lausanne: Elsevier Science SA, 2023, 524(204774), s. nestránkováno. ISSN 0043-1648. [Detail]

ŠIMONOVÁ, Zuzana, Veronika KRBEČKOVÁ, Zuzana VILAMOVÁ, Edmund DOBROČKA, Bořivoj KLEJDUS, Miroslav CIESLAR, Ladislav SVOBODA, Jiří BEDNÁŘ, Richard DVORSKÝ a Jana SEIDLEROVÁ. The Effects of Nature-Inspired Synthesis on Silver Nanoparticle Generation. ACS Omega. American Chemical Society, 2022, 7(6), s. 4850 - 4858. ISSN 2470-1343. [Detail]

KUNČICKÁ, Lenka, Radim KOCICH, Gergely NÉMETH, Karel DVOŘÁK a Marek PAGÁČ. Effect of post process shear straining on structure and mechanical properties of 316 L stainless steel manufactured via powder bed fusion. Additive Manufacturing. 2022, 59(November), s. 103128. ISSN 2214-8604. [Detail]

PREMALATHA, Mariappan, Vadivel VISWANATHAN a Lenka ČEPOVÁ. Application of Semantic Analysis and LSTM-GRU in Developing a Personalized Course Recommendation System. Applied Sciences. BASEL: MDPI Open Access Publishing, 2022, 12(21), s. nestránkováno. ISSN 2076-3417. [Detail]

VLČKOVÁ, Kateřina, Karel FRYDRÝŠEK, Vojtěch BAJTEK, Jiří DEMEL, Leopold PLEVA, Miroslav HAVLÍČEK, Jana POMETLOVÁ, Roman MADEJA, Jiří KRATOCHVÍL, Pavel KRPEC, Pawel OSEMLAK, Kristina ČABANOVÁ, Eva OLŠOVSKÁ a Jana VACULOVÁ. Analytical, Stochastic and Experimental Solution of the Osteosynthesis of the Fifth Metatarsal by Headless Screw. Applied Sciences. BASEL: MDPI Open Access Publishing, 2022, 12(19), s. nestránkováno. ISSN 2076-3417. [Detail]

WILLIAM, Mathias Vijay Albert, Subramanian RAMESH, Robert ČEP, Mahalingam Siva KUMAR a Muniyandy ELANGOVAN. MFO Tunned SVR Models for Analyzing Dimensional Characteristics of Cracks Developed on Steam Generator Tubes. Applied Sciences. BASEL: MDPI Open Access Publishing, 2022, 12(23), s. nestránkováno. ISSN 2076-3417. [Detail]

LUKIC, Dejan, Robert ČEP, Mijodrag MILOSEVIC, Aco ANTIC, Aleksandar ZIVKOVIC, Vladimir TODIC a Dragan RODIC. A Grey Fuzzy Approach to the Selection of Cutting Process from the Aspect of Technological Parameters. Applied Sciences. BASEL: MDPI Open Access Publishing, 2022, 12(24), s. nestránkováno. ISSN 2076-3417. [Detail]

FRYDRÝŠEK, Karel, Ondřej SKOUPÝ, Ivan MRKVICA, Aneta SLANINKOVÁ, Jiří KRATOCHVÍL, Tibor JURGA, Miroslav VLK, Pavel KRPEC, Roman MADEJA, Miroslav HAVLICEK, Dana STANCEKOVA, Jana POMETLOVA a Josef HLINKA. Stochastic Evaluation of Cutting Tool Load and Surface Quality during Milling of HPL. Applied Sciences. BASEL: MDPI Open Access Publishing, 2022, 12(24), s. nestránkováno. ISSN 2076-3417. [Detail]

SEJDA, František, Karel FRYDRÝŠEK, Leopold PLEVA, Martin POMPACH, Josef HLINKA, Marek SADÍLEK, Zuzana MURCINKOVA, Pavel KRPEC, Miroslav HAVLICEK, Roman MADEJA, Jana POMETLOVA, Oldřich UČEŇ a Kamila DOSTÁLOVÁ. Numerical Analysis of the Calcaneal Nail C-NAIL. Applied Sciences. BASEL: MDPI Open Access Publishing, 2022, 12(10), s. nestránkováno. ISSN 2076-3417. [Detail]

FRYDRÝŠEK, Karel, M. ŠÍR, L. PLEVA, J. SZELIGA, J. STRÁNSKÝ, Daniel ČEPICA, Jiří KRATOCHVÍL, J. KOUTECKÝ, R. MADEJA, Kateřina PETEREK DĚDKOVÁ a D. STANČEKOVÁ. Stochastic Strength Analyses of Screws for Femoral Neck Fractures. Applied Sciences. Basilej: MDPI Open Access Publishing, 2022, 12(3), s. nestránkováno. ISSN 2076-3417. [Detail]

FRYDRÝŠEK, Karel, Daniel ČEPICA, Tomáš HALO, Ondřej SKOUPÝ, Leopold PLEVA, Roman MADEJA, Jana POMETLOVÁ, Monika LOSERTOVÁ, Jan KOUTECKÝ, Pavel MICHAL, Vojtěch HAVLAS, Šimon KRAUS, Dominik ĎURICA, Kateřina PETEREK DĚDKOVÁ, Marek PAGÁČ, Pavel KRPEC a Paweł OSEMLAK. Biomechanical Analysis of Staples for Epiphysiodesis. Applied Sciences. Basilej: MDPI Open Access Publishing, 2022, 12(2), s. nestránkováno. ISSN 2076-3417. [Detail]

FRYDRÝŠEK, Karel, Tomáš HALO, Daniel ČEPICA, Vojtěch MACHALLA, Kateřina VLČKOVÁ, Ondřej SKOUPÝ, Roman MADEJA, Miroslav HAVLÍČEK, Kamila DOSTÁLOVÁ, Antonín TREFIL, Leopold PLEVA, Zuzana MURČINKOVÁ, Pavel KRPEC a Josef HLINKA. Biomechanical Assessment of Cannulated Nails for the Treatment of Proximal Femur Fractures. Applied Sciences. Basilej: MDPI Open Access Publishing, 2022, 12(15), s. nestránkováno. ISSN 2076-3417. [Detail]

TIWARI, Tanmay, Akash NAG, Alokesh PRAMANIK a Amit Rai DIXIT. A comparative study of spark assisted bending process using teaching-learning based optimization, desirability approach and genetic algorithm. Applied Soft Computing. San Diego: Elsevier, 2022, 130(November 2022), s. nestránkováno. ISSN 1568-4946. [Detail]

KRZIKALLA, David, Jakub MĚSÍČEK, Radim HALAMA, Jiří HAJNYŠ, Marek PAGÁČ, Tomáš ČEGAN a Jana PETRŮ. On Flexural Properties of Additive Manufactured Composites: Experimental, and Numerical Study. COMPOSITES SCIENCE AND TECHNOLOGY. Elsevier Ltd, 2022, 218(109182), s. nestránkováno. ISSN 0266-3538. [Detail]

MRKVICA, Ivan, Tomáš SZOTKOWSKI, Aneta SLANINKOVÁ a Tibor JURGA. High-Efficiency of PVD Coating Process by Applying an Additional Rotation. Coatings. Basilej: MDPI Open Access Publishing, 2022, 12(6), s. nestránkováno. ISSN 2079-6412. [Detail]

SAXENA, M., A.K. SHARMA, A.K. SRIVASTAVA, R.K. SINGH, A.R. DIXIT, Akash NAG a Sergej HLOCH. Microwave-Assisted Synthesis, Characterization and Tribological Properties of a g-C3N4/MoS2 Nanocomposite for Low Friction Coatings. Coatings. Basilej: MDPI Open Access Publishing, 2022, 12(12), s. nestránkováno. ISSN 2079-6412. [Detail]

KUMAR, Nitesh, Rakesh Kumar SINGH, Ashish Kumar SRIVASTAVA, Akash NAG, Jana PETRŮ a Sergej HLOCH. Surface Modification and Parametric Optimization of Tensile Strength of Al6082/SiC/Waste Material Surface Composite Produced by Friction Stir Processing. Coatings. Basilej: MDPI Open Access Publishing, 2022, 12(12), s. nestránkováno. ISSN 2079-6412. [Detail]

KRAISNIK, Milija, Robert ČEP, Karel KOURIL, Sebastian BALOS, Aco ANTI a Mladomir MILUTINOVIC. Characterization of Microstructural Damage and Failure Mechanisms in C45E Structural Steel under Compressive Load. Crystals. BASEL: MDPI Open Access Publishing, 2022, 12(3), s. nestránkováno. ISSN 2073-4352. [Detail]

ELANGOVAN, Muniyandy, Baskaran SRIMANICKAM, Robert ČEP, Amirtharajan SARANYA a Manickam RAMACHANDRAN. Experimental Study of a Hybrid Solar Collector Using TiO2/Water Nanofluids. Energies. BASEL: MDPI Open Access Publishing, 2022, 15(12), s. nestránkováno. ISSN 1996-1073. [Detail]

ŠIMONOVÁ, Zuzana, Ludmila PORUBOVÁ, Adam VERNER, Roman GABOR, Zuzana VILAMOVÁ, Edmund DOBROČKA, Miroslav CIESLAR, Veronika KRBEČKOVÁ, Kateřina PETEREK DĚDKOVÁ, Ladislav SVOBODA, Jiří BEDNÁŘ, Richard DVORSKÝ a Jana SEIDLEROVÁ. Simple Fabrication of Polycaprolactone-co-lactide Membrane with Silver Nanowires: Synthesis, Characterization and Cytotoxicity Studies. Fibers and Polymers. SEOUL: Korean Fiber Society, 2022, 23(11), s. 2983-2993. ISSN 1229-9197. [Detail]

NESLUSAN, Miroslav, Pavel MINARIK, Robert ČEP, Juraj URICEK, Karel TROJAN, Nikolaj GANEV a Libor TRSKO. Barkhausen noise emission of AISI 304 stainless steel originating from strain induced martensite by shot peening. Journal of Materials Research and Technology. San Diego: Elsevier, 2022, 20(October), s. 748-762. ISSN 2238-7854. [Detail]

SADÍLEK, Marek, Robert ČEP, Lenka ČEPOVÁ, Lukáš KUŠNÍR, Patrik SNIEHOTTA, Katarzyna CZERNÁ a Hana ŠTVERKOVÁ. Production Quality of Shaped Surfaces During Milling. Journal on Systemics, Cybernetics and Informatics. International Institute of Informatics and Systemics, 2022, 20(1), s. 191-208. ISSN 1690-4524. [Detail]

CILLIKOVA, Maria, Anna MICIETOVA, Robert ČEP, Martina JACKOVA, Peter MINARIK, Miroslav NESLUSAN a Karel KOURIL. Analysis of Surface State after Turning of High Tempered Bearing Steel. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(5), s. nestránkováno. ISSN 1996-1944. [Detail]

DAUD, Muhammad Usama, Ghulam ABBAS, Muhammad AFZAAL, Muhammad Yasin NAZ, Nazma Goher FATIMA, Abdul GHUFFAR, Muhammad IRFAN, Mater H MAHNASHI, Stanislaw LEGUTKO, Jiří KRATOCHVÍL, Usama Muhammad NIAZI a Jana PETRŮ. Finite Element Analysis of Silver Nanorods, Spheres, Ellipsoids and Core-Shell Structures for Hyperthermia Treatment of Cancer. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(5), s. nestránkováno. ISSN 1996-1944. [Detail]

AZEEM, Muhammad, Muhammad IRFAN, Manzar MASUD, Gulfam Ul REHMAN, Haider ALI, Muhammad Umair ALI, Amad ZAFAR, Usama MUHAMMAD NIAZI, Saifur RAHMAN, Stanislaw LEGUTKO, Jana PETRŮ a Jiří KRATOCHVÍL. Experimental and Numerical Investigation of Effect of Static and Fatigue Loading on Behavior of Different Double Strap Adhesive Joint Configurations in Fiber Metal Laminates. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(5), s. nestránkováno. ISSN 1996-1944. [Detail]

RUBI, C. Sarala, J. Udaya PRAKASH, Robert ČEP a Muniyandy ELANGOVAN. Optimization of Process Variables in the Drilling of LM6/B4C Composites through Grey Relational Analysis. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(14), s. nestránkováno. ISSN 1996-1944. [Detail]

JOCH, Richard, Michal SAJGALIK, Andrej CZAN, Jozef HOLUBJAK, Miroslav CEDZO a Robert ČEP. Effects of Process Cutting Parameters on the Ti-6Al-4V Turning with Monolithic Driven Rotary Tool. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(15), s. nestránkováno. ISSN 1996-1944. [Detail]

RAMASAMY, Ashok, Sundaram MUNIYASAMY, Robert ČEP a Muniyandy ELANGOVAN. Identification of Fibre Content in Edible Flours Using Microwave Dielectric Cell: Concise Review and Experimental Insights. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(16), s. nestránkováno. ISSN 1996-1944. [Detail]

SARANRAJ, Iyyanar, Sudalaimuthu GANESAN, Lenka ČEPOVÁ, Muniyandy ELANGOVAN a Libor BERANEK. Microstructure, Mechanical and Wear Behaviour of Deep Cryogenically Treated EN 52 Silchrome Valve Steel. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(16), s. nestránkováno. ISSN 1996-1944. [Detail]

SIVAPRAKASAM, Palani, Esayas ABEBE, Robert ČEP a Muniyandy ELANGOVAN. Thermo-Mechanical Behavior of Aluminum Matrix Nano-Composite Automobile Disc Brake Rotor Using Finite Element Method. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(17), s. nestránkováno. ISSN 1996-1944. [Detail]

GEVORKYAN, Edwin, Lenka ČEPOVÁ, Miroslaw RUCKI, Volodymyr NERUBATSKYI, Dmitrij MOROZOW, Wojciech ZUROWSKI, Voskan BARSAMYAN a Karel KOURIL. Activated Sintering of Cr2O3-Based Composites by Hot Pressing. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(17), s. nestránkováno. ISSN 1996-1944. [Detail]

MA QUOC, Phu, Jakub MĚSÍČEK, František FOJTÍK, Jiří HAJNYŠ, Pavel KRPEC, Marek PAGÁČ a Jana PETRŮ. Residual Stress Build-Up in Aluminum Parts Fabricated with SLM Technology Using the Bridge Curvature Method. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(17), s. nestránkováno. ISSN 1996-1944. [Detail]

GEL'ATKO, Matus, Michal HATALA, Frantisek BOTKO, Radoslav VANDZURA a Jiří HAJNYŠ. Eddy Current Testing of Artificial Defects in 316L Stainless Steel Samples Made by Additive Manufacturing Technology. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(19), s. nestránkováno. ISSN 1996-1944. [Detail]

KOSARAC, Aleksandar, Robert ČEP, Miroslav TROCHTA, Milos KNEZEV, Aleksandar ZIVKOVIC, Cvijetin MLADJENOVIC a Aco ANTIC. Thermal Behavior Modeling Based on BP Neural Network in Keras Framework for Motorized Machine Tool Spindles. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(21), s. nestránkováno. ISSN 1996-1944. [Detail]

PIASECKI, Adam, Mateusz KOTKOWIAK, Maciej TULINSKI a Robert ČEP. Tribological Properties of Cu-MoS2-WS2-Ag-CNT Sintered Composite Materials. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(23), s. nestránkováno. ISSN 1996-1944. [Detail]

MUNIR, Muhammad Adnan, Muhammad Yasin NAZ, Shazia SHUKRULLAH, Muhammad Tamoor ANSAR, Muhammad Umar FAROOQ, Muhammad IRFAN, Salim Nasar Faraj MURSAL, Stanislaw Czeslaw LEGUTKO, Jana PETRŮ a Marek PAGÁČ. Enhancement of Magnetic and Dielectric Properties of Ni0.25Cu0.25Zn0.50Fe2O4 Magnetic Nanoparticles through Non-Thermal Microwave Plasma Treatment for High-Frequency and Energy Storage Applications. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(19), s. nestránkováno. ISSN 1996-1944. [Detail]

RAHMAN, Saifur, Rehan KHAN, Usama Muhammad NIAZI, Stanislaw Czeslaw LEGUTKO, Muhammad Ali KHAN, Bilal Anjum AHMED, Jana PETRŮ, Jiří HAJNYŠ a Muhammad IRFAN. Performance Prediction of Erosive Wear of Steel for Two-Phase Flow in an Inverse U-Bend. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(16), s. nestránkováno. ISSN 1996-1944. [Detail]

SHEHERYAR, Muhammad, Muhammad Ali KHAN, Syed Husain Imran JAFFERY, Mansoor ALRUQI, Rehan KHAN, M. Nasir BASHIR a Jana PETRŮ. Multi-Objective Optimization of Process Parameters during Micro-Milling of Nickel-Based Alloy Inconel 718 Using Taguchi-Grey Relation Integrated Approach. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(23), s. nestránkováno. ISSN 1996-1944. [Detail]

ZAIDI, Sajid Raza, Najam UL QADIR, Syed Husain Imran JAFFERY, Muhammad Ali KHAN, Mushtaq KHAN a Jana PETRŮ. Statistical Analysis of Machining Parameters on Burr Formation, Surface Roughness and Energy Consumption during Milling of Aluminium Alloy Al 6061-T6. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(22), s. nestránkováno. ISSN 1996-1944. [Detail]

IRFAN, Muhammad, Irshad AHMAD, Shazia SHUKRULLAH, Humaira HUSSAIN, Muhammad ATIF, Stanislaw LEGUTKO, Jana PETRŮ, Michal HATALA, Muhammad Yasin NAZ a Saifur RAHMAN. Construction of 0D/2D Schottky Heterojunctions of ZnO and Ti3C2 Nanosheets with the Enriched Transfer of Interfacial Charges for Photocatalytic Hydrogen Evolution. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(13), s. nestránkováno. ISSN 1996-1944. [Detail]

SALEEM, Shahroz, Muhammad IRFAN, Muhammad Yasin NAZ, Shazia SHUKRULLAH, Muhammad Adnan MUNIR, Muhammad AYYAZ, Abdullah Saeed ALWADIE, Stanislaw LEGUTKO, Jana PETRŮ a Saifur RAHMAN. Investigating the Impact of Cu2+ Doping on the Morphological, Structural, Optical, and Electrical Properties of CoFe2O4 Nanoparticles for Use in Electrical Devices. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(10), s. nestránkováno. ISSN 1996-1944. [Detail]

ALI, Sadaqat, Muhammad IRFAN, Usama Muhammad NIAZI, Ahmad Majdi Abdul RANI, Ahmad RASHEDI, Saifur RAHMAN, Muhammad Kamal Asif KHAN, Mabkhoot A ALSAIARI, Stanislaw LEGUTKO, Jana PETRŮ a Antonín TREFIL. Microstructure and Mechanical Properties of Modified 316L Stainless Steel Alloy for Biomedical Applications Using Powder Metallurgy. Materials. BASEL: MDPI Open Access Publishing, 2022, 15(8), s. nestránkováno. ISSN 1996-1944. [Detail]

KUDRNA, Lukáš, Phu MA QUOC, Jiří HAJNYŠ, Jakub MĚSÍČEK, Radim HALAMA, František FOJTÍK a Lukáš HORŇÁČEK. Restoration and Possible Upgrade of a Historical Motorcycle Part Using Powder Bed Fusion. Materials. Basilej: MDPI Open Access Publishing, 2022, 15(4), s. nestránkováno. ISSN 1996-1944. [Detail]

RAJESH, P.V., K.K. GUPTA, Robert ČEP, M. RAMACHANDRAN, K. KOUŘIL a K. KALITA. Optimizing Friction Stir Welding of Dissimilar Grades of Aluminum Alloy Using WASPAS. Materials. Basilej: MDPI Open Access Publishing, 2022, 15(5), s. nestránkováno. ISSN 1996-1944. [Detail]

MOHYLA, Petr, Jiří HAJNYŠ, Lucie GEMBALOVÁ, Andrea ZAPLETALOVÁ a Pavel KRPEC. Influence of Heat Treatment of Steel AISI316L Produced by the Selective Laser Melting Method on the Properties of Welded Joint. Materials. Basilej: MDPI Open Access Publishing, 2022, 15(5), s. nestránkováno. ISSN 1996-1944. [Detail]

BRYTAN, Z., M. KRÓL, M. BENEDYK, W. PAKIEŁA, T. TAŃSKI, M.J. DAGNAW, P. SNOPIŃSKI, Marek PAGÁČ a A. CZECH. Microstructural and Mechanical Properties of Novel Co-Free Maraging Steel M789 Prepared by Additive Manufacturing. Materials. Basilej: MDPI Open Access Publishing, 2022, 15(5), s. nestránkováno. ISSN 1996-1944. [Detail]

IRFAN, M., S. SHUKRULLAH, M.Y. NAZ, I. AHMAD, B. SHOUKAT, S. LEGUTKO, Jana PETRŮ, S. RAHMAN a M.A. ALSAIARI. Si/SiO2/Al2O3 Supported Growth of CNT Forest for the Production of La/ZnO/CNT Photocatalyst for Hydrogen Production. Materials. Basilej: MDPI Open Access Publishing, 2022, 15(9), s. nestránkováno. ISSN 1996-1944. [Detail]

MĚSÍČEK, Jakub, Tomáš ČEGAN, Phu MA QUOC, Radim HALAMA, Kateřina SKOTNICOVÁ, Jiří HAJNYŠ, Jan JUŘICA, Pavel KRPEC a Marek PAGÁČ. Effect of artificial aging on the strength, hardness, and residual stress of SLM AlSi10Mg parts prepared from the recycled powder. Materials Science and Engineering. A, Structural Materials : Properties, Microstructure and Processing. Lausanne: Elsevier Science SA, 2022, 855(143900), s. nestránkováno. ISSN 0921-5093. [Detail]

ELAVARASAN, Krishnasamy, Tharmalingam GUNASEKAR, Lenka ČEPOVÁ a Robert ČEP. Study on a Strong and Weak n-Connected Total Perfect k-Dominating set in Fuzzy Graphs. Mathematics. BASEL: MDPI Open Access Publishing, 2022, 10(17), s. nestránkováno. ISSN 2227-7390. [Detail]

THILAGAVATHI, Rajamanickam, Jagadeesan VISWANATH, Lenka ČEPOVÁ a Vladimíra SCHINDLEROVÁ. Effect of Inflation and Permitted Three-Slot Payment on Two-Warehouse Inventory System with Stock-Dependent Demand and Partial Backlogging. Mathematics. BASEL: MDPI Open Access Publishing, 2022, 10(21), s. nestránkováno. ISSN 2227-7390. [Detail]

KALAIVANI, Nagarajan, Khaleel Fayaz Ur RAHMAN, Lenka ČEPOVÁ a Robert ČEP. On Grill S-beta-Open Set in Grill Topological Spaces. Mathematics. BASEL: MDPI Open Access Publishing, 2022, 10(23), s. nestránkováno. ISSN 2227-7390. [Detail]

KRBATA, Michal, Jozef MAJERIK, Igor BARENYI, Maros ECKERT, Robert ČEP, Josef SEDLAK a Ivan SAMARDZIC. EXPERIMENTAL DETERMINATION OF CONTINUOUS COOLING TRANSFORMATION DIAGRAM FOR HIGH STRENGTH STEEL X155CrMoV12. Metalurgija. Záhřeb: Hrvatsko metalurško društvo (HMD), 2022, 61(1), s. 185-188. ISSN 0543-5846. [Detail]

KRBATA, Michal, Jozef MAJERIK, Igor BARENYI, Maros ECKERT, Robert ČEP, Josef SEDLAK a Ivan SAMARDZIC. DILATOMETRIC ANALYSIS OF COOLING CURVES FOR HIGH STRENGTH STEEL X155CrMoV12. Metalurgija. Záhřeb: Hrvatsko metalurško društvo (HMD), 2022, 61(1), s. 193-196. ISSN 0543-5846. [Detail]

IRFAN, Muhammad, Humaira HUSSAIN, Bisma SALEEM, Muhammad SALEEM, Shazia SHUKRULLAH, Stanislaw LEGUTKO, Jana PETRŮ, Muhammad Yasin NAZ, Marek PAGÁČ, Saifur RAHMAN a Rehan KHAN. Evaluation of Ultrasonically ZnO Loading Effect on Photocatalytic Self-Cleaning, UV Protection and Antibacterial Activity of Plasma/Citric Acid-Activated Cotton Fabric. Nanomaterials. BASEL: MDPI Open Access Publishing, 2022, 12(12), s. nestránkováno. ISSN 2079-4991. [Detail]

ZARYBNICKA, Lucie, Jana PETRŮ, Pavel KRPEC a Marek PAGÁČ. Effect of Additives and Print Orientation on the Properties of Laser Sintering-Printed Polyamide 12 Components. Polymers. BASEL: MDPI Open Access Publishing, 2022, 14(6), s. nestránkováno. ISSN 2073-4360. [Detail]

RAJESH, Durvasulu, Nagarajan LENIN, Robert ČEP, Palanivel ANAND a Muniyandy ELANGOVAN. Experimental Investigation of Bi-Directional Flax with Ramie Fibre-Reinforced Phenol-Formaldehyde Hybrid Composites. Polymers. BASEL: MDPI Open Access Publishing, 2022, 14(22), s. nestránkováno. ISSN 2073-4360. [Detail]

GNATOWSKI, Adam, Rafal GOLEBSKI, Jana PETRŮ a Marek PAGÁČ. Analysis of Thermomechanical Properties and the Influence of Machining Process on the Surface Structure of Composites Manufactured from Metal Chips with a Polymer Matrix. Polymers. BASEL: MDPI Open Access Publishing, 2022, 14(17), s. nestránkováno. ISSN 2073-4360. [Detail]

SCHWARZ, David, Marek PAGÁČ, Josef PETRUŠ a Stanislav POLZER. Effect of Water-Induced and Physical Aging on Mechanical Properties of 3D Printed Elastomeric Polyurethane. Polymers. BASEL: MDPI Open Access Publishing, 2022, 14(24), s. nestránkováno. ISSN 2073-4360. [Detail]

RAJENDRAN, Shankar, Narayanan GANESH, Robert ČEP, Rama Chadran NARAYANAN, Subham PAL a Kanak KALITA. A Conceptual Comparison of Six Nature-Inspired Metaheuristic Algorithms in Process Optimization. Processes. BASEL: MDPI Open Access Publishing, 2022, 10(2), s. nestránkováno. ISSN 2227-9717. [Detail]

SHANKAR, Rajendran, Narayanan GANESH, Robert ČEP, Rama Chandran NARAYANAN, Subham PAL a Kanak KALITA. Hybridized Particle Swarm-Gravitational Search Algorithm for Process Optimization. Processes. BASEL: MDPI Open Access Publishing, 2022, 10(3), s. nestránkováno. ISSN 2227-9717. [Detail]

SHANMUGASUNDAR, Govindasamy, Gaurav SAPKOTA, Robert ČEP a Kanak KALITA. Application of MEREC in Multi-Criteria Selection of Optimal Spray-Painting Robot. Processes. BASEL: MDPI Open Access Publishing, 2022, 10(6), s. nestránkováno. ISSN 2227-9717. [Detail]

GAYATHRI, Rajakumaran, Shola Usha RANI, Lenka ČEPOVÁ, Murugesan RAJESH a Kanak KALITA. A Comparative Analysis of Machine Learning Models in Prediction of Mortar Compressive Strength. Processes. BASEL: MDPI Open Access Publishing, 2022, 10(7), s. nestránkováno. ISSN 2227-9717. [Detail]

RENISH, R. Rohith, Amala Justus SELVAM, Robert ČEP a Muniyandy ELANGOVAN. Influence of Varying Compression Ratio of a Compression Ignition Engine Fueled with B20 Blends of Sea Mango Biodiesel. Processes. BASEL: MDPI Open Access Publishing, 2022, 10(7), s. nestránkováno. ISSN 2227-9717. [Detail]

RENISH, R. Rohith, Amala Justus SELVAM, Robert ČEP a Muniyandy ELANGOVAN. Performance, Emission and Combustion Characteristics of a VCR Engine Fueled with Sea Mango Biodiesel/Diesel Blends. Processes. BASEL: MDPI Open Access Publishing, 2022, 10(8), s. nestránkováno. ISSN 2227-9717. [Detail]

SHANMUGASUNDAR, Govindasamy, Tapan Kumar MAHANTA, Robert ČEP a Kanak KALITA. Novel Fuzzy Measurement Alternatives and Ranking according to the Compromise Solution-Based Green Machining Optimization. Processes. BASEL: MDPI Open Access Publishing, 2022, 10(12), s. nestránkováno. ISSN 2227-9717. [Detail]

MAZUR, Tomasz, Lenka ČEPOVÁ, Tomasz SZYMANSKI a Miroslaw RUCKI. Analysis of the Planar Point Identification Accuracy in CMM Measurements. Sensors. BASEL: MDPI Open Access Publishing, 2022, 22(18), s. nestránkováno. ISSN 1424-3210. [Detail]

JAYALAKSHMI, S., N. GANESH, Robert ČEP a J.S. MURUGAN. Movie Recommender Systems: Concepts, Methods, Challenges, and Future Directions. Sensors. MDPI Open Access Publishing, 2022, 22(13), s. nestránkováno. ISSN 1424-3210. [Detail]

VÝTISK, Jan, Stanislav HONUS, Vladimír KOČÍ, Marek PAGÁČ, Jiří HAJNYŠ, Mojmír VRTEK a Milan VUJANOVIC. Comparative study by life cycle assessment of an air ejector and orifice plate for experimental measuring stand manufactured by conventional manufacturing and additive manufacturing. Sustainable Materials and Technologies. Elsevier B.V., 2022, 32, s. July 2022. ISSN 2214-9937. [Detail]

ŠAJDLEROVÁ, Ivana, Vladimíra SCHINDLEROVÁ a Jiří KRATOCHVÍL. POTENTIAL AND LIMITS OF OEE IN THE TOTAL PRODUCTIVITY MANAGEMENT. Advances in Science and Technology Research Journal. Lublin University of Technology, 2021, 14(2), s. 19-26. ISSN 2080-4075. [Detail]

FRYDRÝŠEK, Karel, Sarka MICHENKOVA, Leopold PLEVA, Jan KOUTECKY, Jiří FRIES, Kateřina PETEREK DĚDKOVÁ, Roman MADEJA, Antonín TREFIL, Pavel KRPEC, Tomáš HALO, Leopold HRABOVSKÝ, Lubor BIALY, Roland JANCO a Jiří POKORNÝ. Mechanics of Screw Joints Solved as Beams Placed in a Tangential Elastic Foundation. Applied Sciences. BASEL: MDPI Open Access Publishing, 2021, 11(12), s. nestránkováno. ISSN 2076-3417. [Detail]

PAGÁČ, Marek, Jiří HAJNYŠ, Radim HALAMA, Tariq Abdulaziz A ALDABASH, Jakub MĚSÍČEK, Lukáš JANČAR a Jan JANSA. Prediction of model distortion by fem in 3d printing via the selective laser melting of stainless steel aisi 316l. Applied Sciences. Basilej: MDPI Open Access Publishing, 2021, 11(4), s. 1-16. ISSN 2076-3417. [Detail]

MĚSÍČEK, Jakub, Phu MA QUOC, Jiří HAJNYŠ, Jan ZELINKA, Marek PAGÁČ, Jana PETRŮ a Ondřej MIZERA. Abrasive surface finishing on slm 316l parts fabricated with recycled powder. Applied Sciences. Basilej: MDPI Open Access Publishing, 2021, 11(6), s. nestránkováno. ISSN 2076-3417. [Detail]

DJURDEV, Mica, Robert ČEP, Dejan LUKIC, Aco ANTIC, Branislav POPOVIC a Mijodrag MILOSEVIC. A Genetic Crow Search Algorithm for Optimization of Operation Sequencing in Process Planning. Applied Sciences. MDPI Open Access Publishing, 2021, 11(5), s. 1-22. ISSN 2076-3417. [Detail]

SNOPIŃSKI, P., M. KRÓL, Marek PAGÁČ, Jana PETRŮ, Jiří HAJNYŠ, T. MIKUSZEWSKI a T. TAŃSKI. Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys. Archives of Civil and Mechanical Engineering. Vídeň: Springer, 2021, 21(3), s. nestránkováno. ISSN 1644-9665. [Detail]

SHIVAKOTI, I., G. KIBRIA, Robert ČEP, B.B. PRADHAN a A. SHARMA. Laser surface texturing for biomedical applications: A review. Coatings. Basilej: MDPI Open Access Publishing, 2021, 11(2), s. 1-15. ISSN 2079-6412. [Detail]

PASTOR, Robert, Zdenko BOBOVSKÝ, Petr OŠČÁDAL, Jakub MĚSÍČEK, Marek PAGÁČ, Erik PRADA, Lubica MIKOVA a Ján BABJAK. OPTIMIZING A QUADRUPED ROBOT: A COMPARISON OF TWO METHODS. MM Science Journal. Praha: MM Publishing, 2021, 2021(June), s. 4348-4355. ISSN 1803-1269. [Detail]

MRKVICA, Ivan, Tibor JURGA, Aneta SLANINKOVÁ, Jozef JURKO, Anton PANDA a Pavel KRPEC. DESIGN OF A COMPUTER-AIDED GEAR MANUFACTURING TOOL - RACK-SHAPED CUTTER. MM Science Journal. Praha: MM Publishing, 2021, 2021(December), s. 5403-5409. ISSN 1803-1269. [Detail]

DOSTÁL, Pavel a Marek SADÍLEK. Rationalization of the production of shaped inserts for rotors casting. MM Science Journal. MM Publishing, 2021, 2021(OCT 2021), s. 4803-4809. ISSN 1803-1269. [Detail]

DOSTÁL, Pavel, Marek SADÍLEK, Lukáš KUŠNÍR, Karel KOURIL a Robert ČEP. Increased Cutting Conditions when Machining Heat-Resistant Steel Using Replaceable Inserts. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2021, 21(5), s. 592-599. ISSN 1213-2489. [Detail]

PETRŮ, Jana, Marek PAGÁČ a Martin GREPL. Laser Beam Drilling of Inconel 718 and Its Effect on Mechanical Properties Determined by Static Uniaxial Tensile Testing at Room and Elevated Temperatures. Materials. BASEL: MDPI Open Access Publishing, 2021, 14(11), s. nestránkováno. ISSN 1996-1944. [Detail]

PELIKAN, Lukas, Michal SLANY, Libor BERANEK, Vladislav ANDRONOV, Martin NECAS a Lenka ČEPOVÁ. Experimental Investigation of Suitable Cutting Conditions of Dry Drilling into High-Strength Structural Steel. Materials. BASEL: MDPI Open Access Publishing, 2021, 14(16), s. nestránkováno. ISSN 1996-1944. [Detail]

POKORNÝ, Peter, Štefan VÁCLAV, Jana PETRŮ a Michaela KRITIKOS. Porosity Analysis of Additive Manufactured Parts Using CAQ Technology. Materials. BASEL: MDPI Open Access Publishing, 2021, 14(5), s. nestránkováno. ISSN 1996-1944. [Detail]

BHATTACHARYA, Shibaprasad, Kanak KALITA, Robert ČEP a Shankar CHAKRABORTY. A Comparative Analysis on Prediction Performance of Regression Models during Machining of Composite Materials. Materials. BASEL: MDPI Open Access Publishing, 2021, 14(21), s. nestránkováno. ISSN 1996-1944. [Detail]

STOLARIK, Gabriel, Akash NAG, Jana PETRŮ, Jaroslava SVOBODOVA a Sergej HLOCH. Ultrasonic Pulsating Water Jet Peening: Influence of Pressure and Pattern Strategy. Materials. BASEL: MDPI Open Access Publishing, 2021, 14(20), s. nestránkováno. ISSN 1996-1944. [Detail]

MILOSEVIC, Mijodrag, Robert ČEP, Lenka ČEPOVÁ, Dejan LUKIC, Aco ANTIC a Mica DJURDJEV. A Hybrid Grey Wolf Optimizer for Process Planning Optimization with Precedence Constraints. Materials. BASEL: MDPI Open Access Publishing, 2021, 14(23), s. nestránkováno. ISSN 1996-1944. [Detail]

SRIVASTAVA, Madhulika, Akash NAG, Lucie KREJČÍ, Jana PETRŮ, Somnath CHATTOPADHYAYA a Sergej HLOCH. Effect of Periodic Water Clusters on AISI 304 Welded Surfaces. Materials. BASEL: MDPI Open Access Publishing, 2021, 14(1), s. nestránkováno. ISSN 1996-1944. [Detail]

ČILLIKOVÁ, M., A. MIČIETOVÁ, Robert ČEP, B. MIČIETA, M. NESLUŠAN a P. KEJZLAR. Asymmetrical barkhausen noise of a hard milled surface. Materials. Basilej: MDPI Open Access Publishing, 2021, 14(5), s. 1-12. ISSN 1996-1944. [Detail]

SADÍLEK, Marek, Zdeněk PORUBA, Lenka ČEPOVÁ a M. ŠAJGALÍK. Increasing the accuracy of free-form surface multiaxis milling. Materials. Basilej: MDPI Open Access Publishing, 2021, 14(1), s. 1-16. ISSN 1996-1944. [Detail]

SNOPIŃSKI, P., A. WOŹNIAK a Marek PAGÁČ. Microstructural evolution, hardness, and strengthening mechanisms in SLM AlSi10Mg Alloy subjected to equal-channel angular pressing (ECAP). Materials. Basilej: MDPI Open Access Publishing, 2021, 14(24), s. nestránkováno. ISSN 1996-1944. [Detail]

KOŘÍNEK, Michal, Radim HALAMA, František FOJTÍK, Marek PAGÁČ, Jiří KRČEK, David KRZIKALLA, Radim KOCICH a Lenka KUNČICKÁ. Monotonic Tension-Torsion Experiments and FE Modeling on Notched Specimens Produced by SLM Technology from SS316L. Materials. MDPI Open Access Publishing, 2021, 14(1), s. 1-15. ISSN 1996-1944. [Detail]

POPOVIĆ, B., Lenka ČEPOVÁ, Robert ČEP, M. JANEV a L. KRSTANOVIĆ. Measure of similarity between gmms by embedding of the parameter space that preserves kl divergence. Mathematics. Basilej: MDPI Open Access Publishing, 2021, 9(9), s. nestránkováno. ISSN 2227-7390. [Detail]

SAHARUDIN, Mohd Shahneel, Jiří HAJNYŠ, Tomasz KOZIOR, Damian GOGOLEWSKI a Pawel ZMARZLY. Quality of Surface Texture and Mechanical Properties of PLA and PA-Based Material Reinforced with Carbon Fibers Manufactured by FDM and CFF 3D Printing Technologies. Polymers. BASEL: MDPI Open Access Publishing, 2021, 13(11), s. nestránkováno. ISSN 2073-4360. [Detail]

PAGÁČ, Marek, Jiří HAJNYŠ, Phu MA QUOC, Lukáš JANČAR, Jan JANSA, Petr ŠTEFEK a Jakub MĚSÍČEK. A review of vat photopolymerization technology: Materials, applications, challenges, and future trends of 3d printing. Polymers. Basilej: MDPI Open Access Publishing, 2021, 13(4), s. 1-20. ISSN 2073-4360. [Detail]

KALOVÁ, Martina, Soňa RUSNÁKOVÁ, David KRZIKALLA, Jakub MĚSÍČEK, Radek TOMÁŠEK, Adéla PODEPŘELOVÁ, Marek PAGÁČ a Jiří ROSICKÝ. 3d printed hollow off-axis profiles based on carbon fiber-reinforced polymers: Mechanical testing and finite element method analysis. Polymers. Basilej: MDPI Open Access Publishing, 2021, 13(17), s. nestránkováno. ISSN 2073-4360. [Detail]

SHANMUGASUNDAR, G, M VANITHA, Robert ČEP, Vikas KUMAR, Kanak KALITA a M RAMACHANDRAN. A Comparative Study of Linear, Random Forest and AdaBoost Regressions for Modeling Non-Traditional Machining. Processes. BASEL: MDPI Open Access Publishing, 2021, 9(11), s. nestránkováno. ISSN 2227-9717. [Detail]

MĚSÍČEK, Jakub, Lukáš JANČAR, Phu MA QUOC, Jiří HAJNYŠ, Tomasz TANSKI, Pavel KRPEC a Marek PAGÁČ. Comprehensive View of Topological Optimization Scooter Frame Design and Manufacturing. Symmetry. BASEL: MDPI Open Access Publishing, 2021, 13(7), s. nestránkováno. ISSN 2073-8994. [Detail]

SLANY, Martin, Josef SEDLAK, Jan ZOUHAR, Oskar ZEMCIK, Josef CHLADIL, Ales JAROS, Karel KOURIL, Matus VARHANIK, Jozef MAJERIK, Igor BARENYI a Robert ČEP. Material and Dimensional Analysis of Bimetallic Pipe Bend with Defined Bending Radii. Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2021, 28(3), s. 974-982. ISSN 1330-3651. [Detail]

NAG, A., P. HVIZDOS, A.R. DIXIT, Jana PETRŮ a S. HLOCH. Influence of the frequency and flow rate of a pulsating water jet on the wear damage of tantalum. Wear. Lausanne: Elsevier Science SA, 2021, 477(1), s. nestránkováno. ISSN 0043-1648. [Detail]

PETRŮ, Jana, Lukáš DRÁBEK, Jiří HAJNYŠ, Dalibor JUROK, Marek PAGÁČ a Jakub MĚSÍČEK. Experimental Investigation of Cutting Forces in High-Feed Milling of Titanium Alloy. Advances in Science and Technology Research Journal. Lublin: Lublin University of Technology, 2020, 14(1), s. 89-95. ISSN 2080-4075. [Detail]

HAJNYŠ, Jiří, Marek PAGÁČ, Jakub MĚSÍČEK, Jana PETRŮ a František ŠPALEK. RESEARCH OF 316L METALLIC POWDER FOR USE IN SLM 3D PRINTING. Advances in materials science. Varšava: De Gruyter, 2020, 20(1), s. 5-15. ISSN 2083-4799. [Detail]

KRZIKALLA, David, Aleš SLÍVA, Jakub MĚSÍČEK a Jana PETRŮ. ON MODELLING OF SIMULATION MODEL FOR RACING CAR FRAME TORSIONAL STIFFNESS ANALYSIS. Alexandria Engineering Journal. Elsevier, 2020, 6(59), s. 5123-5133. ISSN 1110-0168. [Detail]

KRÓL, M., M. MUSIORSKI a Marek PAGÁČ. Design and selective laser melting manufacturing of tpe extrusion die. Diffusion and Defect Data Pt.B:Solid State Phenomena. Zurich: Scitec Publications Ltd., 2020, 308, s. 51-63. ISSN 1012-0394. [Detail]

SLÍVA, Aleš, Robert BRÁZDA, Aleš PROCHÁZKA, Jana PETRŮ, Karla ČECH BARABASZOVÁ a Gražyna SIMHA MARTYNKOVÁ. Titanium white modification with silica nanoparticles and formation of structured clusters on vibrating screen. Granular Matter. Springer, 2020, 22(3), s. 1-10. ISSN 1434-5021. [Detail]

DOSTÁL, Pavel, Marek SADÍLEK, Jaroslav DUBSKÝ a Pavel SZKANDERA. ACCURACY OF MACHINE TOOLS. MM Science Journal. Praha: MM Publishing, 2020, 2020(March 2020), s. 3832-3836. ISSN 1803-1269. [Detail]

SZOTKOWSKI, Tomáš, Ivan MRKVICA a Filip KOWALOVSKI. Optimization coating of cylindrical tools with fixture for increasing machine capacity. MM Science Journal. Praha: MM publishing Ltd., 2020, 2020(March), s. 3841-3845. ISSN 1803-1269. [Detail]

LICHOVNÍK, Jiří, Ondřej MIZERA, Marek SADÍLEK, Lenka ČEPOVÁ, Jan ZELINKA a Robert ČEP. Influence of tumbling bodies on surface roughness and geometric deviations by additive sls technology. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2020, 20(3), s. 342-346. ISSN 1213-2489. [Detail]

SHIVAKOTI, Ishwer, Lewlyn L. R RODRIGUES, Robert ČEP, Premendra Mani PRADHAN, Ashis SHARMA a Akash Kumar BHOI. Experimental Investigation and ANFIS-Based Modelling During Machining of EN31 Alloy Steel. Materials. BASEL: MDPI Open Access Publishing, 2020, 13(14), s. nestránkováno. ISSN 1996-1944. [Detail]

KALITA, Kanak, Ranjan Kumar GHADAI, Lenka ČEPOVÁ, Ishwer SHIVAKOTI a Akash Kumar BHOI. Memetic Cuckoo-Search-Based Optimization in Machining Galvanized Iron. Materials. BASEL: MDPI Open Access Publishing, 2020, 13(14), s. nestránkováno. ISSN 1996-1944. [Detail]

MOHYLA, Petr, Jiří HAJNYŠ, Kristýna STERNADELOVÁ, Lucie KREJČÍ, Marek PAGÁČ, Kateřina KONEČNÁ a Pavel KRPEC. Analysis of Welded Joint Properties on an AISI316L Stainless Steel Tube Manufactured by SLM Technology. Materials. BASEL: MDPI Open Access Publishing, 2020, 13(19), s. nestránkováno. ISSN 1996-1944. [Detail]

ČEGAN, Tomáš, Marek PAGÁČ, Jan JUŘICA, Kateřina SKOTNICOVÁ, Jiří HAJNYŠ, Lukáš HORSÁK, Kamil SOUCEK a Pavel KRPEC. Effect of Hot Isostatic Pressing on Porosity and Mechanical Properties of 316 L Stainless Steel Prepared by the Selective Laser Melting Method. Materials. BASEL: MDPI Open Access Publishing, 2020, 13(19), s. nestránkováno. ISSN 1996-1944. [Detail]

KRÓL, M., P. SNOPIŃSKI, Marek PAGÁČ, Jiří HAJNYŠ a Jana PETRŮ. Hot deformation treatment of grain-modified mg-li alloy. Materials. Basilej: MDPI Open Access Publishing, 2020, 13(20), s. 1-13. ISSN 1996-1944. [Detail]

HLINKA, Josef, Martin KRAUS, Jiří HAJNYŠ, Marek PAGÁČ, Jana PETRŮ, Z. BRYTAN a T. TANSKI. Complex corrosion properties of aisi 316L steel prepared by 3D printing technology for possible implant applications. Materials. Basilej: MDPI Open Access Publishing, 2020, 13(7), s. nestránkováno. ISSN 1996-1944. [Detail]

HAJNYŠ, Jiří, Marek PAGÁČ, Jakub MĚSÍČEK, Jana PETRŮ a M KRÓL. Influence of scanning strategy parameters on residual stress in the SLM process according to the bridge curvature method for AISI 316L stainless steel. Materials. Basilej: MDPI Open Access Publishing, 2020, 13(7), s. nestránkováno. ISSN 1996-1944. [Detail]

KRÓL, M., P. SNOPIŃSKI, Jiří HAJNYŠ, Marek PAGÁČ a D. ŁUKOWIEC. Selective laser melting of 18Ni-300 maraging steel. Materials. Basilej: MDPI Open Access Publishing, 2020, 13(19), s. nestránkováno. ISSN 1996-1944. [Detail]

HLAVÁČOVÁ, Irena, Marek SADÍLEK, Petra VÁŇOVÁ, Štefan SZUMILO a Martin TYČ. Influence of Steel Structure on Machinability by Abrasive Water Jet. Materials. MDPI Open Access Publishing, 2020, 13(19), s. 4424(1)-4424(17). ISSN 1996-1944. [Detail]

JUŘÍKOVÁ KUTIOVÁ, Kristýna, Jakub MĚSÍČEK a David KRZIKALLA. Experimental examination of adhesive bonded carbon fibre tube to aluminum alloy aw 7075. Materials Science Forum. Zürich: Trans Tech Publications, 2020, 994(994), s. 125-132. ISSN 1662-9752. [Detail]

LUKIC, D., Robert ČEP, J. VUKMAN, A. ANTIC, M. DJURDJEV a M. MILOSEVIC. Multi-criteria selection of the optimal parameters for high-speed machining of aluminum alloy al7075 thin-walled parts. Metals. Basilej: MDPI Open Access Publishing, 2020, 10(12), s. 1-22. ISSN 2075-4701. [Detail]

KOZÁK, Jindřich, Lucie KREJČÍ, Ivo HLAVATÝ, Robert ČEP a I. SAMARDŽIĆ. Utilization of diffraction analysis in the study of martensitic weld deposits using tungsten carbide particles on s235jr+n steel. Metalurgija. Záhřeb: Hrvatsko metalurško društvo (HMD), 2020, 59(4), s. 470-472. ISSN 0543-5846. [Detail]

HLAVACEK, P., Sergej HLOCH, A. NAG, Jana PETRŮ, M. MULLER, M. HROMASOVÁ a Peter SRNÍČEK. Effect of rotation direction, traverse speed, and abrasive type during the hydroabrasive disintegration of a rotating Ti6Al4V workpiece. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. Londýn: SAGE Publications Ltd, 2020, 1(1), s. nestránkováno. ISSN 0954-4054. [Detail]

PAGÁČ, Marek, David SCHWARZ, Jana PETRŮ a Stanislav POLZER. 3D printed polyurethane exhibits isotropic elastic behavior despite its anisotropic surface. Rapid Prototyping Journal. Bingley: Emerald, 2020, s. nestránkováno. ISSN 1355-2546. [Detail]

MA QUOC, Phu, David KRZIKALLA, Jakub MĚSÍČEK, Jana PETRŮ, Jakub ŠMIRAUS, Aleš SLÍVA a Zdeněk PORUBA. On aluminum honeycomb impact attenuator designs for formula student competitions. Symmetry. Basilej: MDPI Open Access Publishing, 2020, 12(10), s. 1-17. ISSN 2073-8994. [Detail]

JANČAR, Lukáš, Marek PAGÁČ, Jakub MĚSÍČEK a Petr ŠTEFEK. Design procedure of a topologically optimized scooter frame part. Symmetry. Basilej: MDPI Open Access Publishing, 2020, 12(5), s. nestránkováno. ISSN 2073-8994. [Detail]

HUŇAŘ, Marek, Lukáš JANČAR, David KRZIKALLA, D. KAPRINAY a Dávid SRNÍČEK. Comprehensive view on racing car upright design and manufacturing. Symmetry. Basilej: MDPI Open Access Publishing, 2020, 12(6), s. nestránkováno. ISSN 2073-8994. [Detail]

LEHOCKA, Dominika, Frantisek BOTKO, Jiri KLICH, Libor SITEK, Pavol HVIZDOS, Martin FIDES a Robert ČEP. Effect of pulsating water jet disintegration on hardness and elasticity modulus of austenitic stainless steel AISI 304L. The international journal of advanced manufacturing technology. Vídeň: Springer, 2020, x(5-6), s. nestránkováno. ISSN 0268-3768. [Detail]

ZLÁMAL, Tomáš, Ivan MRKVICA, Tomáš SZOTKOWSKI a Šárka MALOTOVÁ. The Influence of Surface Treatment of PVD Coating on Its Quality and Wear Resistant. Coatings. Basilej: MDPI Open Access Publishing, 2019, 9(7), s. nestránkováno. ISSN 2079-6412. [Detail]

KRZIKALLA, David, Jakub MĚSÍČEK, Aleš SLÍVA, Jana PETRŮ a Jakub ŠMIRAUS. Analysis of Torsional Stiffness of the Frame of a Formula Student Vehicle. Journal of Applied Mechanical Engineering. Longdom Publishing, 2019, 8(315), s. 1-5. ISSN 2168-9873. [Detail]

NAG, Akash, Sergej HLOCH, Dominik ČUHA, Amit Rai DIXIT, Jana PETRŮ, Hakan TOZAN, Monika HROMASOVA a Miroslav MUELLER. Acoustic chamber length performance analysis in ultrasonic pulsating water jet erosion of ductile material. Journal of Manufacturing Processes. San Diego: Elsevier, 2019, 47(11/2019), s. 347-356. ISSN 1526-6125. [Detail]

ZLÁMAL, Tomáš, Ivan MRKVICA, Šárka MALOTOVÁ, Ondřej VORTEL a Tomáš VOPAT. EFFECT OF CUTTING TOOL MICROGEOMETRY ON THE ALUMINIUM ALLOY MACHINING PROCESS. MM Průmyslové spektrum. MM Publishing, 2019, 6(6), s. 2915-2919. ISSN 1212-2572. [Detail]

MĚSÍČEK, Jakub, Marek PAGÁČ, Jana PETRŮ, Petr NOVÁK, Jiří HAJNYŠ a Kristýna KUTIOVÁ. Topological optimization of the formula student bell crank. MM Science Journal. Praha: MM Publishing, 2019, 2019(October), s. 2964-2968. ISSN 1803-1269. [Detail]

DOSTÁL, Pavel, Marek SADÍLEK a Radek HRUBÝ. Machining accurate holes with required roughness. MM Science Journal. Praha: MM Publishing, 2019, 2019(October), s. 2969-2974. ISSN 1803-1269. [Detail]

HAJNYŠ, Jiří, Marek PAGÁČ, Kotera ONDŘEJ, Jana PETRŮ a Scholz SEBASTIAN. Influence of basic process parameters on mechanical and internal properties of 316l steel in slm process for renishaw AM400. MM Science Journal. MM Publishing, 2019, s. 2790-2794. ISSN 1803-1269. [Detail]

RUSZ, Stanislav, Ondřej HILŠER, Vladislav OCHODEK, Radek ČADA, Jiří ŠVEC a Pavel SZKANDERA. Influence of SPD Process on Low-Carbon Steel Mechanical Properties. MM Science Journal. MM Publishing, 2019, 12(2), s. 2910-2914. ISSN 1803-1269. [Detail]

KREJČÍ, Lucie, Vladimíra SCHINDLEROVÁ, Michal BUČKO, Ivo HLAVATÝ a M. MICIAN. The Application of PFMEA for Roller Bearings Production. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2019, 19(3), s. 439-445. ISSN 1213-2489. [Detail]

CARACH, Jan, Sergej HLOCH, Jana PETRŮ, Miroslav MUELLER, Monika HROMASOVA, Akash NAG, Dominik CUHA, Petr HLAVACEK, Michal HATALA, Jiří KRATOCHVÍL a Alessandro RUGGIERO. Evaluation of physical phenomena and surface integrity during hydroabrasive disintegration of the rotating workpiece with feedback loop control. Measurement. San Diego: Elsevier, 2019, 134(February 2019), s. 586-594. ISSN 0263-2241. [Detail]

KOZÁK, Jindřich, Lucie KREJČÍ, Ivo HLAVATÝ, Ivan SAMARDŽIČ a Robert ČEP. AN ANALYSIS OF STRUCTURES OCCURRING IN WELD DEPOSIT OF STEEL S235JR N WITH TUNGSTEN CARBIDE PARTICLES AND MARTENSITIC MATRIX. Metalurgija. Hrvatsko metalurško društvo (HMD), 2019, 58(3-4), s. 235-238. ISSN 0543-5846. [Detail]

MALOTOVÁ, Šárka, Robert ČEP, Tomáš ZLÁMAL, Petr MOHYLA, Andrej CZAN, Aco ANTIC, Igor BUDAK a Lobontiu MIRCEA. Evaluation of Residual Stresses after Irregular Interrupted Machining. Tehnički vjesnik – Technical Gazette. University of Osijek, 2019, 25(4), s. 1009-1013. ISSN 1330-3651. [Detail]

ČEP, Robert, Šárka MALOTOVÁ, Jiří LICHOVNÍK, Michal HATALA a Legutko STANISLAW. The influence of cutting conditions on the selected parameters of the surface integrity. Acta Polytechnica. České vysoké učení technické v Praze, 2018, 58(6), s. 334-338. ISSN 1210-2709. [Detail]

STANCEKOVA, Dana, Anna RUDAWSKA, Albert KULLA, Jana PETRŮ a Jozef HOLUBJAK. A CHOICE OF THE OPTIMUM CUTTING RANGES FOR CUTTING NOZZLES A-SD FOR SELECTION OF METALLURGICAL MATERIAL. Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2018, 12(3), s. 106-113. ISSN 2299-8624. [Detail]

KRATOCHVÍL, Jiří, Marek SADÍLEK, Václav MUSIL, Marek PAGÁČ a Dana STANCEKOVA. THE EFFECTIVENESS OF STRATEGIES PRINTING PRINTER EASY 3D MAKER. Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2018, 12(2), s. 197-205. ISSN 2299-8624. [Detail]

PETRŮ, Jana, Tomáš ZLÁMAL, František ŠPALEK a Robert ČEP. SURFACE MICROHARDENING STUDIES ON STEELS AFTER HIGH FEED MILLING. Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2018, 12(2), s. 222-230. ISSN 2299-8624. [Detail]

MICHALSKI, Jakub, Jakub TILL, Jana PETRŮ, Stanislav RUSZ, Ondřej HILŠER a Jiřina VONTOROVÁ. AZ31 magnesium alloy subjected to severe plastic deformation at different temperatures: Microstructure and hardness. IOP Conference Series: Materials Science and Engineering. Volume 385. Institute of Physics, 2018, 461(1), s. 1-6. ISSN 1757-8981. [Detail]

MRKVICA, Ivan, Anton PANDA, Ema NOVÁKOVÁ-MARCINČINOVÁ, Ludmila NOVÁKOVÁ-MARCINČINOVÁ a Tadeusz ZABOROWSKI. PRODUCTION BY FDM METHOD RP TECHNOLOGY FROM PLA ECO-MATERIALS EXTRUDED HORIZONTALLY IN LENGTH. MM Science Journal. MM Publishing, 2018, 11(1), s. 2179-2182. ISSN 1803-1269. [Detail]

MUSIL, Václav, Marek SADÍLEK, Robert ČEP a Šárka MALOTOVÁ. The influence of cutting parameters on surface quality and nitrogen consumption during laser cutting. MM Science Journal. MM Publishing, 2018, 1(June 2018), s. 2363-2366. ISSN 1803-1269. [Detail]

ČEP, Robert, Šárka MALOTOVÁ, Karel KOUŘIL, Lenka ČEPOVÁ, Ladislav KYNCL, Michal ŠAJGALÍK a Tatiana CZÁNOVÁ. Evaluation of residual stress in conditions of irregular interrupted cut. MM Science Journal. MM Publishing, 2018, 2018(October), s. 2436-2440. ISSN 1803-1269. [Detail]

SADÍLEK, Marek, Lukáš KOUSAL, N. NÁPRSTKOVÁ, Tomáš SZOTKOWSKI a Jiří HAJNYŠ. The analysis of accuracy of machined surfaces and surfaces roughness after 3axis and 5axis milling. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2018, 18(6), s. 1015-1022. ISSN 1213-2489. [Detail]

BOTKO, F., M. HATALA, Z. MITALOVA, Robert ČEP, M. RIMAR, A. BERNAT a J. VYBOSTEK. Qualitative evaluation of machined surface of aluminum alloy AlCu4Mg1 depend on feed rate. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2018, 18(2), s. 201-207. ISSN 1213-2489. [Detail]

MĚSÍČEK, Jakub, Michal RICHTÁŘ, Jana PETRŮ, Marek PAGÁČ a Kristýna KUTIOVÁ. Complex view to racing car upright design and manufacturing. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2018, 18(3), s. 449-456. ISSN 1213-2489. [Detail]

MALOTOVÁ, Šárka, Robert ČEP, Jiří KRATOCHVÍL, Michal ŠAJGALÍK a Andrej CZÁN. Dependence of the resistance of the integrated layers on the wear of ceramic cutting tool. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2018, 2018(3), s. 444-448. ISSN 1213-2489. [Detail]

MRKVICA, Ivan, František ŠPALEK a Tomáš SZOTKOWSKI. Influence of Cutting Tool Wear when Milling Inconel 718 on Resulting Roughness. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2018, 18(3), s. 547-461. ISSN 1213-2489. [Detail]

PAGÁČ, Marek, Jiří HAJNYŠ, Jana PETRŮ a Tomáš ZLÁMAL. Comparison of hardness of surface 316L stainless steel made by additive technology and cold rolling. Materials Science Forum. Trans Tech Publications, 2018, 919(2017-11-07), s. 84-91. ISSN 1662-9752. [Detail]

ČEPOVÁ, Lenka, Andrea KOVÁČIKOVÁ, Robert ČEP, Pavel KLAPUT a Ondřej MIZERA. Measurement System Analyses - Gauge Repeatability and Reproducibility Methods. Measurement Science Review. De Gruyter, 2018, 18(1), s. 20-27. ISSN 1335-8871. [Detail]

MAJERIK, Jozef, Rozmarina DUBOVSKA, Jaroslav JAMBOR, Robert ČEP, Jiří KRATOCHVÍL a Karel KOURIL. Experimental Investigation into Wear and Tool Life of Milling Cutter PVD Coated Carbide Inserts While Armox 500 Steel Hard Milling. Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2018, 25(6), s. 1603-1610. ISSN 1330-3651. [Detail]

MALOTOVÁ, Šárka, Robert ČEP, Tomáš ZLÁMAL, Petr MOHYLA, Andrej CZÁN, Aco ANTIC, Igor BUDAK a Lobontiu MIRCEA. Evaluation of Residual Stresses after Irregular Interrupted Machining. Tehnički vjesnik – Technical Gazette. University of Osijek, 2018, 25(4), s. 1009-1013. ISSN 1330-3651. [Detail]

HLAVATÝ, Ivo, Petra HÁJKOVÁ, Lucie KREJČÍ a Robert ČEP. Electric Resistance Welding of Austenitic and Galva nized Steel Sheets. Tehnički vjesnik – Technical Gazette. University of Osijek, 2018, 25(5), s. 1274-1277. ISSN 1330-3651. [Detail]

CÁRACH, J., Sergej HLOCH, Jana PETRŮ, A. NAG, M. GOMBÁR a M HROMASOVÁ. Hydroabrasive disintegration of rotating Monel K-500 workpiece. The international journal of advanced manufacturing technology. Springer, 2018, 96(1-4), s. 981-1001. ISSN 0268-3768. [Detail]

RUDAWSKA, Anna, Albert WIERZCHOWSKI, Miroslav MUELLER, Jana PETRŮ a Natasa NAPRSTKOVA. THE PROPERTIES OF REGENERATIVE POLYMER MASS. Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2017, 11(3), s. 130-138. ISSN 2299-8624. [Detail]

KRATOCHVÍL, Jiří, Jana PETRŮ, Marek PAGÁČ, Jozef HOLUBJAK a Jozef MRAZIK. EFFECT OF CHIP BREAKERS ON THE CUTTING FORCE DURING THE MACHINING OF STEEL C45. Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2017, 11(1), s. 173-178. ISSN 2299-8624. [Detail]

HAJNYŠ, Jiří, Tomáš ZLÁMAL, Jana PETRŮ, Marek PAGÁČ a Anna RUDAWSKA. IMPACT OF CUTTING TOOL GEOMETRY ON THE DYNAMIC LOAD OF SYSTEM IN THE MACHINING PROCESS OF NICKEL ALLOY 625. Advances in science and technology-research journal. Lublin University of Technology, 2017, 10(32), s. 24-31. ISSN 2299-8624. [Detail]

ZLÁMAL, Tomáš, Jiří HAJNYŠ, Jana PETRŮ a Ivan MRKVICA. EFFECT OF THE CUTTING TOOL GEOMETRY ON THE TOOL WEAR RESISTANCE WHEN MACHINING INCONEL 625. Advances in science and technology-research journal. Lublin University of Technology, 2017, 11(4), s. 286-293. ISSN 2299-8624. [Detail]

ČEP, Robert, Ladislav KYNCL, Šárka MALOTOVÁ, Jana PETRŮ, Tomáš ZLÁMAL a Andrej CZÁN. TESTING CERAMICS INSERTS AT IRREGULAR INTERRUPTED CUT ON MATERIAL 14MoV6. Engineering Review. University of Rijeka, 2017, 37(1), s. 67-73. ISSN 1330-9587. [Detail]

MRKVICA, Ivan, Tomáš SZOTKOWSKI, Miroslav JANOŠ, Jana PETRŮ a Tomáš ZLÁMAL. Square Shaped Insert´s Lifetime when Milling Inconel 718. MM Science Journal. MM Publishing, 2017, 10(5), s. 1995-2003. ISSN 1803-1269. [Detail]

ŠPALEK, František, Marek SADÍLEK, Robert ČEP, Jana PETRŮ, Jiří KRATOCHVÍL a Tomáš ČEGAN. Difference between cutting surface of Al foam and solid Al machined by WEDM technology. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2017, 17(5), s. 853-858. ISSN 1213-2489. [Detail]

MRKVICA, Ivan, Tomáš SZOTKOWSKI, Kamil DIHEL, Jozef JURKO a Anton PANDA. Jig design for welding of wind power plant component. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2017, 17(2), s. 237-242. ISSN 1213-2489. [Detail]

MRKVICA, Ivan, Tomáš SZOTKOWSKI, Zbyněk TÝN, Jana PETRŮ a Tomáš ZLÁMAL. Jig design for window frame welding of rail-borne door systems. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2017, 17(4), s. 526-530. ISSN 1213-2489. [Detail]

ŠPALEK, František, Marek SADÍLEK, Robert ČEP, Jana PETRŮ, Jiří KRATOCHVÍL a Tomáš ČEGAN. Difference between Cutting Surface of Al Foam and Solid Al Machined by WEDM Technolo-gy. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2017, 17(5), s. 853-858. ISSN 1213-2489. [Detail]

HAŠOVÁ, Slavomíra, Luboslav STRAKA a František ŠPALEK. Impact assessment of input factors on tool electrode wear in die sinking EDM of Steel EN43CrMo4. Materials Structure & Micromechanics of Fracture. Zürich: Trans Tech Publications, 2017, 756(1), s. 127-135. ISBN 978-3-03835-719-3. [Detail]

PETRŮ, Jana, Tomáš ZLÁMAL, Robert ČEP, Marek SADÍLEK a Dana STANCEKOVA. THE EFFECT OF FEED RATE ON DURABILITY AND WEAR OF EXCHANGEABLE CUTTING INSERTS DURING CUTTING Ni-625. Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2017, 24(Supplement 1), s. 1-6. ISSN 1330-3651. [Detail]

MICIETOVA, Anna, Miroslav NESLUSAN, Robert ČEP, Vladislav OCHODEK, Branislav MICIETA a Marek PAGÁČ. DETECTION OF GRINDING BURN THROUGH THE HIGH AND LOW FREQUENCY BARKHAUSEN NOISE. Tehnički vjesnik – Technical Gazette. University of Osijek, 2017, 24(Supplement 1), s. 71-77. ISSN 1330-3651. [Detail]

HILŠER, Ondřej, Stanislav RUSZ, Lucie KREJČÍ a František ŠPALEK. Grain refinement of extruded AZ31 magnesium alloy by ECAP process. Transactions of the VŠB - Technical University of Ostrava, Mechanical Series. VŠB - Technická univerzita Ostrava, 2017, 63(1), s. 31-37. ISSN 1210-0471. [Detail]

ŠVEC, Jiří, Stanislav RUSZ, Ondřej HILŠER, Vladislav OCHODEK a Lucie KREJČÍ. Mechanical properties of steel DC01 formed by DRECE method. Transactions of the VŠB - Technical University of Ostrava, Mechanical Series. VŠB - Technická univerzita Ostrava, 2017, 63(1), s. 63-72. ISSN 1210-0471. [Detail]

ZLÁMAL, Tomáš, Jana PETRŮ, Ondřej VORTEL, Marek PAGÁČ a Pavel KRAJKOVIČ. MECHANISMS OF CUTTING BLADE WEAR AND THEIR INFLUENCE ON CUTTING ABILITY OF THE TOOL DURING MACHINING SPECIAL ALLOYS. ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL. WARSAW: SOC POLISH MECHANICAL ENGINEERS & TECHNICIANS, 2016, 10(31), s. 144-150. ISSN 2299-8624. [Detail]

HAJNYŠ, Jiří, Tomáš ZLÁMAL, Jana PETRŮ, Marek PAGÁČ a Anna RUDAWSKA. IMPACT OF CUTTING TOOL GEOMETRY ON THE DYNAMIC LOAD OF SYSTEM IN THE MACHINING PROCESS OF NICKEL ALLOY 625. Advances in science and technology-research journal. Lublin University of Technology, 2016, 10(32), s. 24-31. ISSN 2299-8624. [Detail]

MATYSIAK, W., D. BARTKOWSKI, M. HATALA, J. ZAJAC, S. RADCHENKO a Robert ČEP. Study on edgetrimming of holes in the thick steel plates by metal plastic forming technology. Key Engineering Materials. Volume 669. Trans Tech Publications, 2016, 669(669), s. 87-94. ISSN 1013-9826. [Detail]

MRKVICA, Ivan, Vojtěch SLÉHA, Jana PETRŮ, M. NESLUSAN, J. JURKO a A. PANDA. Design of control jig for inserts measurement. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016, 16(1), s. 198-204. ISSN 1213-2489. [Detail]

TICHÁ, Šárka, Ondřej SRBA a Jan VAVŘINA. A measuring device for the checking of 3D indicators. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016, 16(1), s. 280-284. ISSN 1213-2489. [Detail]

ČEPOVÁ, Lenka, Dagmar ŠOKOVÁ, Šárka MALOTOVÁ, Bartosz GAPINSKI a Robert ČEP. Evaluation of cutting forces and surface roughness after machining of selected materials. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016, 16(1), s. 45 - 48. ISSN 1213-2489. [Detail]

PANDA, A., M. PRISLUPČÁK, J. JURKO, I. PANDOVÁ, Ivan MRKVICA a S. LUSCINSKI. The impact of vibration on the technological head. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016, 16(3), s. 579-585. ISSN 1213-2489. [Detail]

MALOTOVÁ, Šárka, Robert ČEP, Lenka ČEPOVÁ, Jana PETRŮ, Dana STANČEKOVÁ, Ladislav KYNCL a Michal HATALA. Roughness Evaluation of the Machined Surface at Interrupted Cutting Process. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2016, 16(1), s. 168-173. ISSN 1213-2489. [Detail]

ŠPALEK, František, Jana PETRŮ, Tomáš ZLÁMAL, Ivan MRKVICA, Robert ČEP a Jiří KRATOCHVÍL. Electro-Erosive Wire Cutting of Aluminum Foam. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2016, 16(2), s. 449-453. ISSN 1213-2489. [Detail]

DUBOVSKÁ, Rosemarina, Jozef MAJERÍK, Robert ČEP a Karel KOUŘIL. INVESTIGATING THE INFLUENCE OF CUTTING SPEED ON THE TOOL LIFE OF CUTTING INSERT IN CUTTING THE DIN 1.4301 STEEL. Materiali in tehnologije. Inštitut za kovinske materiale in tehnologije, 2016, 50(3), s. 439-445. ISSN 1580-2949. [Detail]

STANCEKOVA, D., D. STEKLAC, Jana PETRŮ, Tomáš ZLÁMAL, Marek SADÍLEK, M. JANOTA a M. KORDIK. Influence of machining and heat treatment on deformations of thin-walled bearings. Metallography XV : selected, peer reviewed papers from the International Symposium on Metallography (Metallography 2013), April 24-26, 2013, Stará Lesná, Slovak Republic. Zürich: Trans Tech Publications, 2016, 862(1), s. 49-58. ISBN 978-3-03835-740-7. [Detail]

SADÍLEK, Marek, Jaroslav DUBSKÝ, Zuzana SADÍLKOVÁ a Zdeněk PORUBA. Cutting forces during turning with variable depth of cut. Perspectives in Science. Elsevier, 2016, 2016(7), s. 357-363. ISBN 0-000-00000-0. [Detail]

ČEP, Robert, Šárka MALOTOVÁ, Marek PAGÁČ, Marek SADÍLEK a Jiří LICHOVNÍK. Parameters Influence of CO2 Laser on Cutting Quality of Polymer Materials. Sborník vědeckých prací Vysoké školy báňské - Technické univerzity Ostrava. Řada strojní. Vysoká škola báňská - Technická univerzita Ostrava, 2016, LXII(1/2016), s. 9-16. ISSN 1210-0471. [Detail]

BRYCHTA, Petr, Marek SADÍLEK a Josef BRYCHTA. The influence of motor skills on measurement accuracy. Technologické inžinierstvo. University of Žilina, 2016, 13(1), s. 22-23. ISSN 1336-5967. [Detail]

MRKVICA, Ivan, Miroslav NESLUSAN, Robert ČEP a Vojtěch SLÉHA. PROPERTIES AND COMPARISON OF PVD COATINGS. Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2016, 23(2), s. 569-574. ISSN 1330-3651. [Detail]

CARACH, Jan, Sergej HLOCH, Petr HLAVAEK, Jiri SCUCKA, Petr MARTINEC, Jana PETRŮ, Tomáš ZLÁMAL, Michal ZELENAK, Peter MONKA, Dominika LEHOCKA a Jolanta KROLCZYK. Tangential turning of Incoloy alloy 925 using abrasive water jet technology. The international journal of advanced manufacturing technology. New York: Springer, 2016, 82(9-12), s. 1747-1752. ISSN 0268-3768. [Detail]

MRKVICA, Ivan, Jozef JURKO a Tadeusz ZABOROVSKI. Elementary study of the machinability during drilling of stainless steels X2Cr18Ni8. MECHANIK-Miesiecznik Naukowo-Techniczny. Agenda Wydawnicza SIMP, 2015, 2015(4), s. K111-115. ISSN 0025-6552. [Detail]

MRKVICA, Ivan, Jana PETRŮ, Vojtěch SLÉHA, Miroslav NESLUŠAN, Jozef JUROK a Anton PANDA. Properties of cutting inserts with different PVD coatings. MM Science Journal. MM Publishing, 2015, 2015(June), s. 600-603. ISSN 1803-1269. [Detail]

PETRŮ, Jana, Jan SCHIFFNER, Tomáš ZLÁMAL, Marek SADÍLEK a Dana STANČEKOVÁ. Investigations of Cutting Tool Wear While Machining Inconel 718. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2015, 15(3), s. 396-403. ISSN 1213-2489. [Detail]

ČILIKOVÁ, Mária, Branislav MIČIETA, Miroslav NESLUŠAN, Robert ČEP, Ivan MRKVICA, Jana PETRŮ a Tomáš ZLÁMAL. Prediction of the catastrophic tool failure in hard turning through acoustic emission. Materiali in tehnologije. Inštitut za kovinske materiale in tehnologije, 2015, 49(3), s. 355-363. ISSN 1580-2949. [Detail]

MRKVICA, Ivan, Miroslav NESLUŠAN, Anna MIČIETOVÁ, Mária ČILLIKOVÁ a Branislav MIČIETA. Detection of tool breakage during hard turning through acoustic emission at low removal rates. Measurement. Elsevier, 2015, 70(1), s. 1-13. ISSN 0263-2241. [Detail]

PORUBA, Zdeněk, Jiří PODEŠVA, Ondřej FRANTIŠEK, Martin FUSEK, Robert BRÁZDA a Marek SADÍLEK. Strength Analysis and Optimization of Welding Robot Mechanism in Emergency Stop State. Perspectives in Science. Elsevier, 2015, 7C(December 2015), s. 347-352. ISBN 0-000-00000-0. [Detail]

TICHÁ, Šárka a Jan BOTEK. THE MODERN MEASUREMENT TECHNOLOGY AND CHECKING OF SHAFTS PARAMETERS. Technologické inžinierstvo. University of Žilina, 2015, Volume XII(2/2015), s. 28-30. ISSN 1336-5967. [Detail]

RADVANSKÁ, Agáta, Pavol HREHA, Lucia KNAPČÍKOVÁ, Jana PETRŮ, Tomáš ZLÁMAL a Peter MONKA. Influence of focusing tube wear on vibrations and surface roughness. Tehnički vjesnik – Technical Gazette. University of Osijek, 2015, 22(2), s. 270-278. ISSN 1330-3651. [Detail]

RADVANSKÁ, Agáta, Jana PETRŮ, Katarína MONKOVÁ, Tomáš ZLÁMAL, Pavol HREHA, Matej ŠOMŠÁK, Andrej ANDREJ a Branimir ŠAFRAN. Rationalization of manufacturing of plastic injection moulds by abrasive waterjet. Tehnički vjesnik – Technical Gazette. University of Osijek, 2015, 22(2), s. 521-525. ISSN 1330-3651. [Detail]

SADÍLEK, Marek, František FOJTÍK, Zuzana SADÍLKOVÁ, Kamil KOLAŘÍK a Jana PETRŮ. A STUDY OF EFFECTS OF CHANGING THE POSITION OF THE TOOL AXIS TO THE MACHINED SURFACE. Transactions of Famena. University of Zagreb, 2015, 39(2), s. 33-46. ISSN 1333-1124. [Detail]

PETRŮ, Jana, Tomáš ZLÁMAL, Robert ČEP a Lenka ČEPOVÁ. Technology of Thermal Spray Coating Machining. International Journal of Mechanical, Aerospace, Industrial and Mechatronics Engineering. Amsterdam: World Academy of Science, Engineering and Technology, 2014, 86(1), s. 854-857. ISSN 1307-6892. [Detail]

ČEP, Robert, Adam JANÁSEK, Jana PETRŮ, Marek SADÍLEK, Petr MOHYLA, Jan VALÍČEK, Marta HARNIČÁROVÁ a Andrej CZAN. Surface roughness after machining and influence of feed rate on process. Key engineering materials. Volume 581. Trans Tech Publications, 2014, 581(1), s. 341-347. ISSN 1013-9826. [Detail]

KOURIL, Karel, Robert ČEP, Adam JANÁSEK, Antonin KRIZ a Dana STANCEKOVA. Surface Integrity at Reaming Operation by MT3 Head. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2014, 14(2), s. 193-199. ISSN 1213-2489. [Detail]

KYNCL, Ladislav, Marek SADÍLEK, Robert ČEP, Jana PETRŮ, Dana STANČEKOVÁ, Josef PROCHÁZKA a Pavel NOVÁČEK. Tests of drills during drilling holes into alloy wheels. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2014, 14(4), s. 554-561. ISSN 1213-2489. [Detail]

PETRŮ, Jana, Tomáš ZLÁMAL, Ivan MRKVICA a Robert ČEP. The effect of thermal shocks on wear of exchangeable sintered carbide inserts during the cutting process. Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2014, 14(4), s. 590-596. ISSN 1213-2489. [Detail]

MOHYLA, Petr, Zdeněk KUBOŇ, Robert ČEP a Ivan SAMARDZIC. Evaluation of Creep Properties of Steel P92 and its Welded Joint. Metalurgija. Hrvatsko metalurško društvo (HMD), 2014, 53(2), s. 175-178. ISSN 0543-5846. [Detail]

MOHYLA, Petr, Zdeněk KUBOŇ, Robert ČEP, Adam JANÁSEK a Ivan SAMARDZIC. Secondary Hardening of Low-Alloyed Creep-Resistant Steel Welds. Metalurgija. Hrvatsko metalurško društvo (HMD), 2014, 53(1), s. 25-28. ISSN 0543-5846. [Detail]

SADÍLEK, Marek, Jiří KRATOCHVÍL, Jana PETRŮ, Robert ČEP, Tomáš ZLÁMAL a Dana STANČEKOVÁ. Cutting tool wear monitoring with the use of impedance layers. Tehnički vjesnik – Technical Gazette. University of Osijek, 2014, 3(21), s. 639-644. ISSN 1330-3651. [Detail]

MRKVICA, Ivan, Jozef JURKO, Anton PANDA a Marcel BEHÚN. Prediction of selected aspects of machinability of austenitic stainless steels. Advanced Materials Research. Zürich: Trans Tech Publication Ltd, 2013, 739(739), s. 206-209. ISSN 1022-6680. [Detail]

JANČÍKOVÁ, Zora, Pavol KOŠTIAL, Dana BAKOŠOVÁ, David SEIDL, Jiří DAVID, Jan VALÍČEK a Marie HARNIČÁROVÁ. Neural Model for Prediction of Tires Eigenfrequencies. Advanced Structured Materials. Volume 32. Heidelberg: Springer, 2013, 41(1), s. 1-11. ISSN 1869-8433. [Detail]

MRKVICA, Ivan, Ryszard KONDERLA, Jozef JURKO, Anton PANDA a Miroslav NESLUŠAN. Force load of cutting tool by turning of nickel alloy Inconel 718 with sintered carbide insert. Applied Mechanics and Materials. Volume 409-410. Trans Tech Publications, 2013, 372(372), s. 441-444. ISSN 1660-9336. [Detail]

JANČÍKOVÁ, Zora, Pavol KOŠTIAL, Ivan RUŽIAK, Jan VALÍČEK, Karel FRYDRÝŠEK, Richard PUCHKÝ a Martina FARKAŠOVÁ. Thermo-Mechanical Analysis of Rubber Compounds Filled by Carbon Nanotubes. Defect and Diffusion Forum. VII. Enfield, New Hampshire: Trans Tech Publications, 2013, 336(1), s. 1-10. ISSN 1012-0386. [Detail]

KOŠTIAL, Pavol, D BAKOŠOVÁ, Zora JANČÍKOVÁ, Ivan RUŽIAK a Jan VALÍČEK. Thermo-mechanical analysis of rubber compounds filled by carbon nanotubes. Deffect and Diffusion Forum. Durnten-Zurich: Trans Tech Publications, 2013, 336(1), s. 1-10. ISSN 1662-9507. [Detail]

JANČÍKOVÁ, Zora, Pavol KOŠTIAL, Dana BAKOŠOVÁ, Ivan RUŽIAK, Karel FRYDRÝŠEK, Jan VALÍČEK, Martina FARKAŠOVÁ a Richard PUCHKÝ. The Study of Electrical Transport in Rubber Blends Filled by Single Wall Carbon Nanotubes. Journal of Nano Research. Enfield, New Hampshire: Trans Tech Publications, 2013, 16(21), s. 1-6. ISSN 1662-5250. [Detail]

MRKVICA, Ivan, Miroslav NESLUŠAN a Anna MIČIETOVÁ. Study of elastic deformations in hard turning. Key Engineering Materials. Volume 592-593. Trans Tech Publications, 2013, 581(581), s. 194-201. ISSN 1013-9826. [Detail]

MRKVICA, Ivan a Miroslav JANOŠ. Comparison of round insert´s lifetime when milling Inconel 718. Key Engineering Materials. Volume 592-593. Trans Tech Publications, 2013, 581(581), s. 26-31. ISSN 1013-9826. [Detail]

ČEP, Robert, Adam JANÁSEK, Jana PETRŮ, Lenka ČEPOVÁ, Andrej CZÁN a Jan VALÍČEK. Hard machinable machining of cobalt-based superalloy. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2013, 13(2), s. 142-147. ISSN 1213-2489. [Detail]

MRKVICA, Ivan, Ryszard KONDERLA, Miroslav NESLUŠAN, Jozef JURKO a Anton PANDA. Cutting forces by turning of Inconel 718 with inserts from different materials. Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2013, 13(4), s. 499-504. ISSN 1213-2489. [Detail]

SADÍLEK, Marek, Robert ČEP, Zuzana SADÍLKOVÁ, Jan VALÍČEK a Lenka PETŘKOVSKÁ. Increasing tool life in turning with variable depth of cut. Materiali in tehnologije. Ljubljana: Inštitut za kovinske materiale in tehnologije, 2013, 47(2), s. 199-203. ISSN 1580-2949. [Detail]

NESLUSAN, Miroslav, Ivan MRKVICA, Robert ČEP a Maria CILLIKOVA. INFLUENCE OF CUTTING SPEED ON INTENSITY OF THE PLASTIC DEFORMATION DURING HARD CUTTING. Materiali in tehnologije. Ljubljana: Inštitut za kovinske materiale in tehnologije, 2013, 47(NOV-DEC 2013), s. 745-755. ISSN 1580-2949. [Detail]

KOŠTIAL, Pavol, Zora JANČÍKOVÁ, Jan VALÍČEK, Marta HARNIČÁROVÁ, Dana BAKOŠOVÁ a Ivo ŠPIČKA. Artificial Neural Networks Application in Modal Analysis of Tires. Measurement Science Review. Warsaw: De Gruyter, 2013, 13(5), s. 273-278. ISSN 1335-8871. [Detail]

TICHÁ, Šárka, Ondřej SRBA a Jan VAVŘINA. KALIBRACE 3D TASTERů. Strojírenská technologie. Ústí nad Labem,: Univerzita J. E. Purkyně, Ústav techniky a řízení výroby, 2013, 1(2), s. 125-130. ISSN 1211-4162. [Detail]

MRKVICA, Ivan, Ryszard KONDERLA a Miroslav NESLUŠAN. Silové zatížení nástroje při soustružení niklové slitiny Inconel 718 nástrojem s VBD ze slinutého karbidu. Strojírenská technologie. Ústí nad Labem,: Univerzita J. E. Purkyně, Ústav techniky a řízení výroby, 2013, XVIII(4), s. 258-265. ISSN 1211-4162. [Detail]

MRKVICA, Ivan a Miroslav JANOŠ. The milling of material Inconel 718 with indexables cutting inserts from sintered carbide. Technologické inžinierstvo. Žilina: University of Žilina, 2013, X(1), s. 9-11. ISSN 1336-5967. [Detail]

ANTIC, Aco, Drazan KOZAK, Borut KOSEC, Goran SIMUNOVIC, Tomislav SARIC, Dusan KOVACEVIC a Robert ČEP. INFLUENCE OF TOOL WEAR ON THE MECHANISM OF CHIPS SEGMENTATION AND TOOL VIBRATION. Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2013, 20(1), s. 105-112. ISSN 1330-3651. [Detail]

ČEP, Robert, Adam JANÁSEK, Lenka ČEPOVÁ, Jana PETRŮ, Ivo HLAVATÝ, Zlatan CAR a Michal HATALA. EXPERIMENTAL TESTING OF EXCHANGEABLE CUTTING INSERTS CUTTING ABILITY. Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2013, 20(1), s. 21-26. ISSN 1330-3651. [Detail]

ČEP, Robert, Adam JANÁSEK, Aleš SLÍVA, Miroslav NESLUŠAN a Martin BINDER. EXPERIMENTAL TOOL LIFE TESTS OF INDEXABLE INSERTS FOR STAINLESS STEEL MACHINING. Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2013, 20(6), s. 933-940. ISSN 1330-3651. [Detail]

SADÍLEK, Marek, Jiří KRATOCHVÍL a Lenka PETŘKOVSKÁ. Turning Thin-Walled Workpieces with Variable Depth of Cut. World Academy of Science, Engineering and Technology. Blackpool: WASET, 2013, 1(1), s. 1232–1236. ISSN 2010-376X. [Detail]