ZLÁMAL, Tomáš, Ivan MRKVICA, Tomáš SZOTKOWSKI and Šárka MALOTOVÁ. The Influence of Surface Treatment of PVD Coating on Its Quality and Wear Resistant.
Coatings. Basilej: MDPI Open Access Publishing, 2019,
9(7), p. nestránkováno. ISSN 2079-6412.
[Detail] KRZIKALLA, David, Jakub MĚSÍČEK, Aleš SLÍVA, Jana PETRŮ and Jakub ŠMIRAUS. Analysis of Torsional Stiffness of the Frame of a Formula Student Vehicle.
Journal of Applied Mechanical Engineering. Longdom Publishing, 2019,
8(315), p. 1-5. ISSN 2168-9873.
[Detail] NAG, Akash, Sergej HLOCH, Dominik ČUHA, Amit Rai DIXIT, Jana PETRŮ, Hakan TOZAN, Monika HROMASOVA and Miroslav MUELLER. Acoustic chamber length performance analysis in ultrasonic pulsating water jet erosion of ductile material.
Journal of Manufacturing Processes. San Diego: Elsevier, 2019,
47(11/2019), p. 347-356. ISSN 1526-6125.
[Detail] ZLÁMAL, Tomáš, Ivan MRKVICA, Šárka MALOTOVÁ, Ondřej VORTEL and Tomáš VOPAT. EFFECT OF CUTTING TOOL MICROGEOMETRY ON THE ALUMINIUM ALLOY MACHINING PROCESS.
MM Průmyslové spektrum. MM Publishing, 2019,
6(6), p. 2915-2919. ISSN 1212-2572.
[Detail] MĚSÍČEK, Jakub, Marek PAGÁČ, Jana PETRŮ, Petr NOVÁK, Jiří HAJNYŠ and Kristýna KUTIOVÁ. Topological optimization of the formula student bell crank.
MM Science Journal. Praha: MM Publishing, 2019,
2019(October), p. 2964-2968. ISSN 1803-1269.
[Detail] DOSTÁL, Pavel, Marek SADÍLEK and Radek HRUBÝ. Machining accurate holes with required roughness.
MM Science Journal. Praha: MM Publishing, 2019,
2019(October), p. 2969-2974. ISSN 1803-1269.
[Detail] HAJNYŠ, Jiří, Marek PAGÁČ, Kotera ONDŘEJ, Jana PETRŮ and Scholz SEBASTIAN. Influence of basic process parameters on mechanical and internal properties of 316l steel in slm process for renishaw AM400.
MM Science Journal. MM Publishing, 2019, p. 2790-2794. ISSN 1803-1269.
[Detail] RUSZ, Stanislav, Ondřej HILŠER, Vladislav OCHODEK, Radek ČADA, Jiří ŠVEC and Pavel SZKANDERA. Influence of SPD Process on Low-Carbon Steel Mechanical Properties.
MM Science Journal. MM Publishing, 2019,
12(2), p. 2910-2914. ISSN 1803-1269.
[Detail] KREJČÍ, Lucie, Vladimíra SCHINDLEROVÁ, Michal BUČKO, Ivo HLAVATÝ and M. MICIAN. The Application of PFMEA for Roller Bearings Production.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2019,
19(3), p. 439-445. ISSN 1213-2489.
[Detail] CARACH, Jan, Sergej HLOCH, Jana PETRŮ, Miroslav MUELLER, Monika HROMASOVA, Akash NAG, Dominik CUHA, Petr HLAVACEK, Michal HATALA, Jiří KRATOCHVÍL and Alessandro RUGGIERO. Evaluation of physical phenomena and surface integrity during hydroabrasive disintegration of the rotating workpiece with feedback loop control.
Measurement. San Diego: Elsevier, 2019,
134(February 2019), p. 586-594. ISSN 0263-2241.
[Detail] KOZÁK, Jindřich, Lucie KREJČÍ, Ivo HLAVATÝ, Ivan SAMARDŽIČ and Robert ČEP. AN ANALYSIS OF STRUCTURES OCCURRING IN WELD DEPOSIT OF STEEL S235JR N WITH TUNGSTEN CARBIDE PARTICLES AND MARTENSITIC MATRIX.
Metalurgija. Hrvatsko metalurško društvo (HMD), 2019,
58(3-4), p. 235-238. ISSN 0543-5846.
[Detail] MALOTOVÁ, Šárka, Robert ČEP, Tomáš ZLÁMAL, Petr MOHYLA, Andrej CZAN, Aco ANTIC, Igor BUDAK and Lobontiu MIRCEA. Evaluation of Residual Stresses after Irregular Interrupted Machining.
Tehnički vjesnik – Technical Gazette. University of Osijek, 2019,
25(4), p. 1009-1013. ISSN 1330-3651.
[Detail] ČEP, Robert, Šárka MALOTOVÁ, Jiří LICHOVNÍK, Michal HATALA and Legutko STANISLAW. The influence of cutting conditions on the selected parameters of the surface integrity.
Acta Polytechnica. České vysoké učení technické v Praze, 2018,
58(6), p. 334-338. ISSN 1210-2709.
[Detail] STANCEKOVA, Dana, Anna RUDAWSKA, Albert KULLA, Jana PETRŮ and Jozef HOLUBJAK. A CHOICE OF THE OPTIMUM CUTTING RANGES FOR CUTTING NOZZLES A-SD FOR SELECTION OF METALLURGICAL MATERIAL.
Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2018,
12(3), p. 106-113. ISSN 2299-8624.
[Detail] KRATOCHVÍL, Jiří, Marek SADÍLEK, Václav MUSIL, Marek PAGÁČ and Dana STANCEKOVA. THE EFFECTIVENESS OF STRATEGIES PRINTING PRINTER EASY 3D MAKER.
Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2018,
12(2), p. 197-205. ISSN 2299-8624.
[Detail] PETRŮ, Jana, Tomáš ZLÁMAL, František ŠPALEK and Robert ČEP. SURFACE MICROHARDENING STUDIES ON STEELS AFTER HIGH FEED MILLING.
Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2018,
12(2), p. 222-230. ISSN 2299-8624.
[Detail] MICHALSKI, Jakub, Jakub TILL, Jana PETRŮ, Stanislav RUSZ, Ondřej HILŠER and Jiřina VONTOROVÁ. AZ31 magnesium alloy subjected to severe plastic deformation at different temperatures: Microstructure and hardness.
IOP Conference Series: Materials Science and Engineering. Volume 385. Institute of Physics, 2018,
461(1), p. 1-6. ISSN 1757-8981.
[Detail] MRKVICA, Ivan, Anton PANDA, Ema NOVÁKOVÁ-MARCINČINOVÁ, Ludmila NOVÁKOVÁ-MARCINČINOVÁ and Tadeusz ZABOROWSKI. PRODUCTION BY FDM METHOD RP TECHNOLOGY FROM PLA ECO-MATERIALS EXTRUDED HORIZONTALLY IN LENGTH.
MM Science Journal. MM Publishing, 2018,
11(1), p. 2179-2182. ISSN 1803-1269.
[Detail] MUSIL, Václav, Marek SADÍLEK, Robert ČEP and Šárka MALOTOVÁ. The influence of cutting parameters on surface quality and nitrogen consumption during laser cutting.
MM Science Journal. MM Publishing, 2018,
1(June 2018), p. 2363-2366. ISSN 1803-1269.
[Detail] ČEP, Robert, Šárka MALOTOVÁ, Karel KOUŘIL, Lenka ČEPOVÁ, Ladislav KYNCL, Michal ŠAJGALÍK and Tatiana CZÁNOVÁ. Evaluation of residual stress in conditions of irregular interrupted cut.
MM Science Journal. MM Publishing, 2018,
2018(October), p. 2436-2440. ISSN 1803-1269.
[Detail] SADÍLEK, Marek, Lukáš KOUSAL, N. NÁPRSTKOVÁ, Tomáš SZOTKOWSKI and Jiří HAJNYŠ. The analysis of accuracy of machined surfaces and surfaces roughness after 3axis and 5axis milling.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2018,
18(6), p. 1015-1022. ISSN 1213-2489.
[Detail] BOTKO, F., M. HATALA, Z. MITALOVA, Robert ČEP, M. RIMAR, A. BERNAT and J. VYBOSTEK. Qualitative evaluation of machined surface of aluminum alloy AlCu4Mg1 depend on feed rate.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2018,
18(2), p. 201-207. ISSN 1213-2489.
[Detail] MĚSÍČEK, Jakub, Michal RICHTÁŘ, Jana PETRŮ, Marek PAGÁČ and Kristýna KUTIOVÁ. Complex view to racing car upright design and manufacturing.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2018,
18(3), p. 449-456. ISSN 1213-2489.
[Detail] MALOTOVÁ, Šárka, Robert ČEP, Jiří KRATOCHVÍL, Michal ŠAJGALÍK and Andrej CZÁN. Dependence of the resistance of the integrated layers on the wear of ceramic cutting tool.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2018,
2018(3), p. 444-448. ISSN 1213-2489.
[Detail] MRKVICA, Ivan, František ŠPALEK and Tomáš SZOTKOWSKI. Influence of Cutting Tool Wear when Milling Inconel 718 on Resulting Roughness.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2018,
18(3), p. 547-461. ISSN 1213-2489.
[Detail] PAGÁČ, Marek, Jiří HAJNYŠ, Jana PETRŮ and Tomáš ZLÁMAL. Comparison of hardness of surface 316L stainless steel made by additive technology and cold rolling.
Materials Science Forum. Trans Tech Publications, 2018,
919(2017-11-07), p. 84-91. ISSN 1662-9752.
[Detail] ČEPOVÁ, Lenka, Andrea KOVÁČIKOVÁ, Robert ČEP, Pavel KLAPUT and Ondřej MIZERA. Measurement System Analyses - Gauge Repeatability and Reproducibility Methods.
Measurement Science Review. De Gruyter, 2018,
18(1), p. 20-27. ISSN 1335-8871.
[Detail] MAJERIK, Jozef, Rozmarina DUBOVSKA, Jaroslav JAMBOR, Robert ČEP, Jiří KRATOCHVÍL and Karel KOURIL. Experimental Investigation into Wear and Tool Life of Milling Cutter PVD Coated Carbide Inserts While Armox 500 Steel Hard Milling.
Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2018,
25(6), p. 1603-1610. ISSN 1330-3651.
[Detail] MALOTOVÁ, Šárka, Robert ČEP, Tomáš ZLÁMAL, Petr MOHYLA, Andrej CZÁN, Aco ANTIC, Igor BUDAK and Lobontiu MIRCEA. Evaluation of Residual Stresses after Irregular Interrupted Machining.
Tehnički vjesnik – Technical Gazette. University of Osijek, 2018,
25(4), p. 1009-1013. ISSN 1330-3651.
[Detail] HLAVATÝ, Ivo, Petra HÁJKOVÁ, Lucie KREJČÍ and Robert ČEP. Electric Resistance Welding of Austenitic and Galva nized Steel Sheets.
Tehnički vjesnik – Technical Gazette. University of Osijek, 2018,
25(5), p. 1274-1277. ISSN 1330-3651.
[Detail] CÁRACH, J., Sergej HLOCH, Jana PETRŮ, A. NAG, M. GOMBÁR and M HROMASOVÁ. Hydroabrasive disintegration of rotating Monel K-500 workpiece.
The international journal of advanced manufacturing technology. Springer, 2018,
96(1-4), p. 981-1001. ISSN 0268-3768.
[Detail] RUDAWSKA, Anna, Albert WIERZCHOWSKI, Miroslav MUELLER, Jana PETRŮ and Natasa NAPRSTKOVA. THE PROPERTIES OF REGENERATIVE POLYMER MASS.
Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2017,
11(3), p. 130-138. ISSN 2299-8624.
[Detail] KRATOCHVÍL, Jiří, Jana PETRŮ, Marek PAGÁČ, Jozef HOLUBJAK and Jozef MRAZIK. EFFECT OF CHIP BREAKERS ON THE CUTTING FORCE DURING THE MACHINING OF STEEL C45.
Advances in science and technology-research journal. Lublin: Lublin University of Technology, 2017,
11(1), p. 173-178. ISSN 2299-8624.
[Detail] HAJNYŠ, Jiří, Tomáš ZLÁMAL, Jana PETRŮ, Marek PAGÁČ and Anna RUDAWSKA. IMPACT OF CUTTING TOOL GEOMETRY ON THE DYNAMIC LOAD OF SYSTEM IN THE MACHINING PROCESS OF NICKEL ALLOY 625.
Advances in science and technology-research journal. Lublin University of Technology, 2017,
10(32), p. 24-31. ISSN 2299-8624.
[Detail] ZLÁMAL, Tomáš, Jiří HAJNYŠ, Jana PETRŮ and Ivan MRKVICA. EFFECT OF THE CUTTING TOOL GEOMETRY ON THE TOOL WEAR RESISTANCE WHEN MACHINING INCONEL 625.
Advances in science and technology-research journal. Lublin University of Technology, 2017,
11(4), p. 286-293. ISSN 2299-8624.
[Detail] ČEP, Robert, Ladislav KYNCL, Šárka MALOTOVÁ, Jana PETRŮ, Tomáš ZLÁMAL and Andrej CZÁN. TESTING CERAMICS INSERTS AT IRREGULAR INTERRUPTED CUT ON MATERIAL 14MoV6.
Engineering Review. University of Rijeka, 2017,
37(1), p. 67-73. ISSN 1330-9587.
[Detail] MRKVICA, Ivan, Tomáš SZOTKOWSKI, Miroslav JANOŠ, Jana PETRŮ and Tomáš ZLÁMAL. Square Shaped Insert´s Lifetime when Milling Inconel 718.
MM Science Journal. MM Publishing, 2017,
10(5), p. 1995-2003. ISSN 1803-1269.
[Detail] ŠPALEK, František, Marek SADÍLEK, Robert ČEP, Jana PETRŮ, Jiří KRATOCHVÍL and Tomáš ČEGAN. Difference between cutting surface of Al foam and solid Al machined by WEDM technology.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2017,
17(5), p. 853-858. ISSN 1213-2489.
[Detail] MRKVICA, Ivan, Tomáš SZOTKOWSKI, Kamil DIHEL, Jozef JURKO and Anton PANDA. Jig design for welding of wind power plant component.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2017,
17(2), p. 237-242. ISSN 1213-2489.
[Detail] MRKVICA, Ivan, Tomáš SZOTKOWSKI, Zbyněk TÝN, Jana PETRŮ and Tomáš ZLÁMAL. Jig design for window frame welding of rail-borne door systems.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2017,
17(4), p. 526-530. ISSN 1213-2489.
[Detail] ŠPALEK, František, Marek SADÍLEK, Robert ČEP, Jana PETRŮ, Jiří KRATOCHVÍL and Tomáš ČEGAN. Difference between Cutting Surface of Al Foam and Solid Al Machined by WEDM Technolo-gy.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2017,
17(5), p. 853-858. ISSN 1213-2489.
[Detail] HAŠOVÁ, Slavomíra, Luboslav STRAKA and František ŠPALEK. Impact assessment of input factors on tool electrode wear in die sinking EDM of Steel EN43CrMo4.
Materials Structure & Micromechanics of Fracture. Zürich: Trans Tech Publications, 2017,
756(1), p. 127-135. ISBN 978-3-03835-719-3.
[Detail] PETRŮ, Jana, Tomáš ZLÁMAL, Robert ČEP, Marek SADÍLEK and Dana STANCEKOVA. THE EFFECT OF FEED RATE ON DURABILITY AND WEAR OF EXCHANGEABLE CUTTING INSERTS DURING CUTTING Ni-625.
Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2017,
24(Supplement 1), p. 1-6. ISSN 1330-3651.
[Detail] MICIETOVA, Anna, Miroslav NESLUSAN, Robert ČEP, Vladislav OCHODEK, Branislav MICIETA and Marek PAGÁČ. DETECTION OF GRINDING BURN THROUGH THE HIGH AND LOW FREQUENCY BARKHAUSEN NOISE.
Tehnički vjesnik – Technical Gazette. University of Osijek, 2017,
24(Supplement 1), p. 71-77. ISSN 1330-3651.
[Detail] HILŠER, Ondřej, Stanislav RUSZ, Lucie KREJČÍ and František ŠPALEK. Grain refinement of extruded AZ31 magnesium alloy by ECAP process.
Transactions of the VŠB - Technical University of Ostrava, Mechanical Series. VŠB - Technická univerzita Ostrava, 2017,
63(1), p. 31-37. ISSN 1210-0471.
[Detail] ŠVEC, Jiří, Stanislav RUSZ, Ondřej HILŠER, Vladislav OCHODEK and Lucie KREJČÍ. Mechanical properties of steel DC01 formed by DRECE method.
Transactions of the VŠB - Technical University of Ostrava, Mechanical Series. VŠB - Technická univerzita Ostrava, 2017,
63(1), p. 63-72. ISSN 1210-0471.
[Detail] ZLÁMAL, Tomáš, Jana PETRŮ, Ondřej VORTEL, Marek PAGÁČ and Pavel KRAJKOVIČ. MECHANISMS OF CUTTING BLADE WEAR AND THEIR INFLUENCE ON CUTTING ABILITY OF THE TOOL DURING MACHINING SPECIAL ALLOYS.
ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL. WARSAW: SOC POLISH MECHANICAL ENGINEERS & TECHNICIANS, 2016,
10(31), p. 144-150. ISSN 2299-8624.
[Detail] HAJNYŠ, Jiří, Tomáš ZLÁMAL, Jana PETRŮ, Marek PAGÁČ and Anna RUDAWSKA. IMPACT OF CUTTING TOOL GEOMETRY ON THE DYNAMIC LOAD OF SYSTEM IN THE MACHINING PROCESS OF NICKEL ALLOY 625.
Advances in science and technology-research journal. Lublin University of Technology, 2016,
10(32), p. 24-31. ISSN 2299-8624.
[Detail] MATYSIAK, W., D. BARTKOWSKI, M. HATALA, J. ZAJAC, S. RADCHENKO and Robert ČEP. Study on edgetrimming of holes in the thick steel plates by metal plastic forming technology.
Key Engineering Materials. Volume 669. Trans Tech Publications, 2016,
669(669), p. 87-94. ISSN 1013-9826.
[Detail] MRKVICA, Ivan, Vojtěch SLÉHA, Jana PETRŮ, M. NESLUSAN, J. JURKO and A. PANDA. Design of control jig for inserts measurement.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016,
16(1), p. 198-204. ISSN 1213-2489.
[Detail] TICHÁ, Šárka, Ondřej SRBA and Jan VAVŘINA. A measuring device for the checking of 3D indicators.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016,
16(1), p. 280-284. ISSN 1213-2489.
[Detail] ČEPOVÁ, Lenka, Dagmar ŠOKOVÁ, Šárka MALOTOVÁ, Bartosz GAPINSKI and Robert ČEP. Evaluation of cutting forces and surface roughness after machining of selected materials.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016,
16(1), p. 45 - 48. ISSN 1213-2489.
[Detail] PANDA, A., M. PRISLUPČÁK, J. JURKO, I. PANDOVÁ, Ivan MRKVICA and S. LUSCINSKI. The impact of vibration on the technological head.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2016,
16(3), p. 579-585. ISSN 1213-2489.
[Detail] MALOTOVÁ, Šárka, Robert ČEP, Lenka ČEPOVÁ, Jana PETRŮ, Dana STANČEKOVÁ, Ladislav KYNCL and Michal HATALA. Roughness Evaluation of the Machined Surface at Interrupted Cutting Process.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2016,
16(1), p. 168-173. ISSN 1213-2489.
[Detail] ŠPALEK, František, Jana PETRŮ, Tomáš ZLÁMAL, Ivan MRKVICA, Robert ČEP and Jiří KRATOCHVÍL. Electro-Erosive Wire Cutting of Aluminum Foam.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2016,
16(2), p. 449-453. ISSN 1213-2489.
[Detail] DUBOVSKÁ, Rosemarina, Jozef MAJERÍK, Robert ČEP and Karel KOUŘIL. INVESTIGATING THE INFLUENCE OF CUTTING SPEED ON THE TOOL LIFE OF CUTTING INSERT IN CUTTING THE DIN 1.4301 STEEL.
Materiali in tehnologije. Inštitut za kovinske materiale in tehnologije, 2016,
50(3), p. 439-445. ISSN 1580-2949.
[Detail] STANCEKOVA, D., D. STEKLAC, Jana PETRŮ, Tomáš ZLÁMAL, Marek SADÍLEK, M. JANOTA and M. KORDIK. Influence of machining and heat treatment on deformations of thin-walled bearings.
Metallography XV : selected, peer reviewed papers from the International Symposium on Metallography (Metallography 2013), April 24-26, 2013, Stará Lesná, Slovak Republic. Zürich: Trans Tech Publications, 2016,
862(1), p. 49-58. ISBN 978-3-03835-740-7.
[Detail] SADÍLEK, Marek, Jaroslav DUBSKÝ, Zuzana SADÍLKOVÁ and Zdeněk PORUBA. Cutting forces during turning with variable depth of cut.
Perspectives in Science. Elsevier, 2016,
2016(7), p. 357-363. ISBN 0-000-00000-0.
[Detail] ČEP, Robert, Šárka MALOTOVÁ, Marek PAGÁČ, Marek SADÍLEK and Jiří LICHOVNÍK. Parameters Influence of CO2 Laser on Cutting Quality of Polymer Materials.
Sborník vědeckých prací Vysoké školy báňské - Technické univerzity Ostrava. Řada strojní. Vysoká škola báňská - Technická univerzita Ostrava, 2016,
LXII(1/2016), p. 9-16. ISSN 1210-0471.
[Detail] BRYCHTA, Petr, Marek SADÍLEK and Josef BRYCHTA. The influence of motor skills on measurement accuracy.
Technologické inžinierstvo. University of Žilina, 2016,
13(1), p. 22-23. ISSN 1336-5967.
[Detail] MRKVICA, Ivan, Miroslav NESLUSAN, Robert ČEP and Vojtěch SLÉHA. PROPERTIES AND COMPARISON OF PVD COATINGS.
Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2016,
23(2), p. 569-574. ISSN 1330-3651.
[Detail] CARACH, Jan, Sergej HLOCH, Petr HLAVAEK, Jiri SCUCKA, Petr MARTINEC, Jana PETRŮ, Tomáš ZLÁMAL, Michal ZELENAK, Peter MONKA, Dominika LEHOCKA and Jolanta KROLCZYK. Tangential turning of Incoloy alloy 925 using abrasive water jet technology.
The international journal of advanced manufacturing technology. New York: Springer, 2016,
82(9-12), p. 1747-1752. ISSN 0268-3768.
[Detail] MRKVICA, Ivan, Jozef JURKO and Tadeusz ZABOROVSKI. Elementary study of the machinability during drilling of stainless steels X2Cr18Ni8.
MECHANIK-Miesiecznik Naukowo-Techniczny. Agenda Wydawnicza SIMP, 2015,
2015(4), p. K111-115. ISSN 0025-6552.
[Detail] MRKVICA, Ivan, Jana PETRŮ, Vojtěch SLÉHA, Miroslav NESLUŠAN, Jozef JUROK and Anton PANDA. Properties of cutting inserts with different PVD coatings.
MM Science Journal. MM Publishing, 2015,
2015(June), p. 600-603. ISSN 1803-1269.
[Detail] PETRŮ, Jana, Jan SCHIFFNER, Tomáš ZLÁMAL, Marek SADÍLEK and Dana STANČEKOVÁ. Investigations of Cutting Tool Wear While Machining Inconel 718.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2015,
15(3), p. 396-403. ISSN 1213-2489.
[Detail] ČILIKOVÁ, Mária, Branislav MIČIETA, Miroslav NESLUŠAN, Robert ČEP, Ivan MRKVICA, Jana PETRŮ and Tomáš ZLÁMAL. Prediction of the catastrophic tool failure in hard turning through acoustic emission.
Materiali in tehnologije. Inštitut za kovinske materiale in tehnologije, 2015,
49(3), p. 355-363. ISSN 1580-2949.
[Detail] MRKVICA, Ivan, Miroslav NESLUŠAN, Anna MIČIETOVÁ, Mária ČILLIKOVÁ and Branislav MIČIETA. Detection of tool breakage during hard turning through acoustic emission at low removal rates.
Measurement. Elsevier, 2015,
70(1), p. 1-13. ISSN 0263-2241.
[Detail] PORUBA, Zdeněk, Jiří PODEŠVA, Ondřej FRANTIŠEK, Martin FUSEK, Robert BRÁZDA and Marek SADÍLEK. Strength Analysis and Optimization of Welding Robot Mechanism in Emergency Stop State.
Perspectives in Science. Elsevier, 2015,
7C(December 2015), p. 347-352. ISBN 0-000-00000-0.
[Detail] TICHÁ, Šárka and Jan BOTEK. THE MODERN MEASUREMENT TECHNOLOGY AND CHECKING OF SHAFTS PARAMETERS.
Technologické inžinierstvo. University of Žilina, 2015,
Volume XII(2/2015), p. 28-30. ISSN 1336-5967.
[Detail] RADVANSKÁ, Agáta, Pavol HREHA, Lucia KNAPČÍKOVÁ, Jana PETRŮ, Tomáš ZLÁMAL and Peter MONKA. Influence of focusing tube wear on vibrations and surface roughness.
Tehnički vjesnik – Technical Gazette. University of Osijek, 2015,
22(2), p. 270-278. ISSN 1330-3651.
[Detail] RADVANSKÁ, Agáta, Jana PETRŮ, Katarína MONKOVÁ, Tomáš ZLÁMAL, Pavol HREHA, Matej ŠOMŠÁK, Andrej ANDREJ and Branimir ŠAFRAN. Rationalization of manufacturing of plastic injection moulds by abrasive waterjet.
Tehnički vjesnik – Technical Gazette. University of Osijek, 2015,
22(2), p. 521-525. ISSN 1330-3651.
[Detail] SADÍLEK, Marek, František FOJTÍK, Zuzana SADÍLKOVÁ, Kamil KOLAŘÍK and Jana PETRŮ. A STUDY OF EFFECTS OF CHANGING THE POSITION OF THE TOOL AXIS TO THE MACHINED SURFACE.
Transactions of Famena. University of Zagreb, 2015,
39(2), p. 33-46. ISSN 1333-1124.
[Detail] PETRŮ, Jana, Tomáš ZLÁMAL, Robert ČEP and Lenka ČEPOVÁ. Technology of Thermal Spray Coating Machining.
International Journal of Mechanical, Aerospace, Industrial and Mechatronics Engineering. Amsterdam: World Academy of Science, Engineering and Technology, 2014,
86(1), p. 854-857. ISSN 1307-6892.
[Detail] ČEP, Robert, Adam JANÁSEK, Jana PETRŮ, Marek SADÍLEK, Petr MOHYLA, Jan VALÍČEK, Marta HARNIČÁROVÁ and Andrej CZAN. Surface roughness after machining and influence of feed rate on process.
Key engineering materials. Volume 581. Trans Tech Publications, 2014,
581(1), p. 341-347. ISSN 1013-9826.
[Detail] KOURIL, Karel, Robert ČEP, Adam JANÁSEK, Antonin KRIZ and Dana STANCEKOVA. Surface Integrity at Reaming Operation by MT3 Head.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2014,
14(2), p. 193-199. ISSN 1213-2489.
[Detail] KYNCL, Ladislav, Marek SADÍLEK, Robert ČEP, Jana PETRŮ, Dana STANČEKOVÁ, Josef PROCHÁZKA and Pavel NOVÁČEK. Tests of drills during drilling holes into alloy wheels.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2014,
14(4), p. 554-561. ISSN 1213-2489.
[Detail] PETRŮ, Jana, Tomáš ZLÁMAL, Ivan MRKVICA and Robert ČEP. The effect of thermal shocks on wear of exchangeable sintered carbide inserts during the cutting process.
Manufacturing Technology. Univerzita Jana Evangelisty Purkyně, 2014,
14(4), p. 590-596. ISSN 1213-2489.
[Detail] MOHYLA, Petr, Zdeněk KUBOŇ, Robert ČEP and Ivan SAMARDZIC. Evaluation of Creep Properties of Steel P92 and its Welded Joint.
Metalurgija. Hrvatsko metalurško društvo (HMD), 2014,
53(2), p. 175-178. ISSN 0543-5846.
[Detail] MOHYLA, Petr, Zdeněk KUBOŇ, Robert ČEP, Adam JANÁSEK and Ivan SAMARDZIC. Secondary Hardening of Low-Alloyed Creep-Resistant Steel Welds.
Metalurgija. Hrvatsko metalurško društvo (HMD), 2014,
53(1), p. 25-28. ISSN 0543-5846.
[Detail] SADÍLEK, Marek, Jiří KRATOCHVÍL, Jana PETRŮ, Robert ČEP, Tomáš ZLÁMAL and Dana STANČEKOVÁ. Cutting tool wear monitoring with the use of impedance layers.
Tehnički vjesnik – Technical Gazette. University of Osijek, 2014,
3(21), p. 639-644. ISSN 1330-3651.
[Detail] MRKVICA, Ivan, Jozef JURKO, Anton PANDA and Marcel BEHÚN. Prediction of selected aspects of machinability of austenitic stainless steels.
Advanced Materials Research. Zürich: Trans Tech Publication Ltd, 2013,
739(739), p. 206-209. ISSN 1022-6680.
[Detail] JANČÍKOVÁ, Zora, Pavol KOŠTIAL, Dana BAKOŠOVÁ, David SEIDL, Jiří DAVID, Jan VALÍČEK and Marie HARNIČÁROVÁ. Neural Model for Prediction of Tires Eigenfrequencies.
Advanced Structured Materials. Volume 32. Heidelberg: Springer, 2013,
41(1), p. 1-11. ISSN 1869-8433.
[Detail] MRKVICA, Ivan, Ryszard KONDERLA, Jozef JURKO, Anton PANDA and Miroslav NESLUŠAN. Force load of cutting tool by turning of nickel alloy Inconel 718 with sintered carbide insert.
Applied Mechanics and Materials. Volume 409-410. Trans Tech Publications, 2013,
372(372), p. 441-444. ISSN 1660-9336.
[Detail] JANČÍKOVÁ, Zora, Pavol KOŠTIAL, Ivan RUŽIAK, Jan VALÍČEK, Karel FRYDRÝŠEK, Richard PUCHKÝ and Martina FARKAŠOVÁ. Thermo-Mechanical Analysis of Rubber Compounds Filled by Carbon Nanotubes.
Defect and Diffusion Forum. VII. Enfield, New Hampshire: Trans Tech Publications, 2013,
336(1), p. 1-10. ISSN 1012-0386.
[Detail] KOŠTIAL, Pavol, D BAKOŠOVÁ, Zora JANČÍKOVÁ, Ivan RUŽIAK and Jan VALÍČEK. Thermo-mechanical analysis of rubber compounds filled by carbon nanotubes.
Deffect and Diffusion Forum. Durnten-Zurich: Trans Tech Publications, 2013,
336(1), p. 1-10. ISSN 1662-9507.
[Detail] JANČÍKOVÁ, Zora, Pavol KOŠTIAL, Dana BAKOŠOVÁ, Ivan RUŽIAK, Karel FRYDRÝŠEK, Jan VALÍČEK, Martina FARKAŠOVÁ and Richard PUCHKÝ. The Study of Electrical Transport in Rubber Blends Filled by Single Wall Carbon Nanotubes.
Journal of Nano Research. Enfield, New Hampshire: Trans Tech Publications, 2013,
16(21), p. 1-6. ISSN 1662-5250.
[Detail] MRKVICA, Ivan, Miroslav NESLUŠAN and Anna MIČIETOVÁ. Study of elastic deformations in hard turning.
Key Engineering Materials. Volume 592-593. Trans Tech Publications, 2013,
581(581), p. 194-201. ISSN 1013-9826.
[Detail] MRKVICA, Ivan and Miroslav JANOŠ. Comparison of round insert´s lifetime when milling Inconel 718.
Key Engineering Materials. Volume 592-593. Trans Tech Publications, 2013,
581(581), p. 26-31. ISSN 1013-9826.
[Detail] ČEP, Robert, Adam JANÁSEK, Jana PETRŮ, Lenka ČEPOVÁ, Andrej CZÁN and Jan VALÍČEK. Hard machinable machining of cobalt-based superalloy.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2013,
13(2), p. 142-147. ISSN 1213-2489.
[Detail] MRKVICA, Ivan, Ryszard KONDERLA, Miroslav NESLUŠAN, Jozef JURKO and Anton PANDA. Cutting forces by turning of Inconel 718 with inserts from different materials.
Manufacturing Technology. Ústí nad Labem: Univerzita Jana Evangelisty Purkyně, 2013,
13(4), p. 499-504. ISSN 1213-2489.
[Detail] SADÍLEK, Marek, Robert ČEP, Zuzana SADÍLKOVÁ, Jan VALÍČEK and Lenka PETŘKOVSKÁ. Increasing tool life in turning with variable depth of cut.
Materiali in tehnologije. Ljubljana: Inštitut za kovinske materiale in tehnologije, 2013,
47(2), p. 199-203. ISSN 1580-2949.
[Detail] NESLUSAN, Miroslav, Ivan MRKVICA, Robert ČEP and Maria CILLIKOVA. INFLUENCE OF CUTTING SPEED ON INTENSITY OF THE PLASTIC DEFORMATION DURING HARD CUTTING.
Materiali in tehnologije. Ljubljana: Inštitut za kovinske materiale in tehnologije, 2013,
47(NOV-DEC 2013), p. 745-755. ISSN 1580-2949.
[Detail] KOŠTIAL, Pavol, Zora JANČÍKOVÁ, Jan VALÍČEK, Marta HARNIČÁROVÁ, Dana BAKOŠOVÁ and Ivo ŠPIČKA. Artificial Neural Networks Application in Modal Analysis of Tires.
Measurement Science Review. Warsaw: De Gruyter, 2013,
13(5), p. 273-278. ISSN 1335-8871.
[Detail] TICHÁ, Šárka, Ondřej SRBA and Jan VAVŘINA. KALIBRACE 3D TASTERů.
Strojírenská technologie. Ústí nad Labem,: Univerzita J. E. Purkyně, Ústav techniky a řízení výroby, 2013,
1(2), p. 125-130. ISSN 1211-4162.
[Detail] MRKVICA, Ivan, Ryszard KONDERLA and Miroslav NESLUŠAN. Silové zatížení nástroje při soustružení niklové slitiny Inconel 718 nástrojem s VBD ze slinutého karbidu.
Strojírenská technologie. Ústí nad Labem,: Univerzita J. E. Purkyně, Ústav techniky a řízení výroby, 2013,
XVIII(4), p. 258-265. ISSN 1211-4162.
[Detail] MRKVICA, Ivan and Miroslav JANOŠ. The milling of material Inconel 718 with indexables cutting inserts from sintered carbide.
Technologické inžinierstvo. Žilina: University of Žilina, 2013,
X(1), p. 9-11. ISSN 1336-5967.
[Detail] ANTIC, Aco, Drazan KOZAK, Borut KOSEC, Goran SIMUNOVIC, Tomislav SARIC, Dusan KOVACEVIC and Robert ČEP. INFLUENCE OF TOOL WEAR ON THE MECHANISM OF CHIPS SEGMENTATION AND TOOL VIBRATION.
Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2013,
20(1), p. 105-112. ISSN 1330-3651.
[Detail] ČEP, Robert, Adam JANÁSEK, Lenka ČEPOVÁ, Jana PETRŮ, Ivo HLAVATÝ, Zlatan CAR and Michal HATALA. EXPERIMENTAL TESTING OF EXCHANGEABLE CUTTING INSERTS CUTTING ABILITY.
Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2013,
20(1), p. 21-26. ISSN 1330-3651.
[Detail] ČEP, Robert, Adam JANÁSEK, Aleš SLÍVA, Miroslav NESLUŠAN and Martin BINDER. EXPERIMENTAL TOOL LIFE TESTS OF INDEXABLE INSERTS FOR STAINLESS STEEL MACHINING.
Tehnički vjesnik – Technical Gazette. Osijek: University of Osijek, 2013,
20(6), p. 933-940. ISSN 1330-3651.
[Detail] SADÍLEK, Marek, Jiří KRATOCHVÍL and Lenka PETŘKOVSKÁ. Turning Thin-Walled Workpieces with Variable Depth of Cut.
World Academy of Science, Engineering and Technology. Blackpool: WASET, 2013,
1(1), p. 1232–1236. ISSN 2010-376X.
[Detail]